» Topics » Advice »Automatic machine - connect in the village and in the country

Automatic machine - connect in the village and in the country



I connected the machine to the machine using an additional pump. The scheme is not new, found on the internet. Everything works fine.
The pump Rucheek, made in Belarus, is connected to the intake valves of the machine. When the valves open, power is supplied to the pump and it pumps water. Shakes perfectly, no worse than in the apartment, the powder from the tray is washed instantly.
In general, such machines require pressure in the region from 1 to 10 atmospheres, and a vibration pump theoretically produces up to 6 atmospheres, this is enough.

The pump must be connected via a relay, the valves operate from 220V. Relay has not yet been found, made by myself. I have an assembly of a 12V / 30A automotive relay, a 30V printer power supply. To prevent the relay from warming up from 30V, a 12V lamp is switched on in series with it. When the relay turns on, the light is on.
The machine erases perfectly, is controlled even faster by 5-10 minutes.

By the way, I tried to let water out and by gravity from a height of two meters — water comes in, but sooooo slowly, the machine gets tired of waiting and turns on the suction of water, in short a program error. It was even poured manually through the tray, but this can only be washed and squeezed. There are only 3 rinses, each time you fill up with water.

The consumption for ordinary washing is 50 liters of water, the pump is in a container of an appropriate size.

Suitable for topic

Related topics

Add a comment

    • smilesmilesxaxaokdontknowyahoonea
      bossscratchfoolyesyes-yesaggressivesecret
      sorrydancedance2dance3pardonhelpdrinks
      stopfriendsgoodgoodgoodwhistleswoontongue
      smokeclappingcraydeclarederisivedon-t_mentiondownload
      heatirefullaugh1mdameetingmoskingnegative
      not_ipopcornpunishreadscarescaressearch
      tauntthank_youthisto_clueumnikacuteagree
      badbeeeblack_eyeblum3blushboastboredom
      censoredpleasantrysecret2threatenvictoryyusun_bespectacled
      shokrespektlolprevedwelcomekrutoyya_za
      ya_dobryihelperne_huliganne_othodifludbanclose
7 comments
Maybe. Only the current of the PM coil must be watched. The smallest, as a rule, consume at least 0.3 A to operate. If the relay of the machine can withstand then it is possible.
Well, do not forget that the power supply of the SM and additional switching must necessarily go through an RCD or YES with a tripping current of no more than 30 mA, even if there is no grounding conductor.
Author
soon I will do research with hydrodrilling ...may be able to find up to 10 meters, but this is extremely unlikely. It would be nice. Well, my former well is the third attempt to find water in this area. Near the wells are more than 20 meters and they are empty.
Although .... Well, there is something about the wells, they wrote in depths of six meters ....
Dmitry ... And "hydrophore" instead of "brook"? )))) And don’t have to rely, and there will also be water in the kitchen! ....)))
We're not looking for easy ways? ))))
If the problem is only in the relay, then it may be instead of him to put a magnetic starter through some kind of connector. Although cumbersome, it’s easier to find, and his contacts are powerful.
Author
Yes, I’ll buy a relay for 220V, the city is small, you won’t find it.

Previously, washing took a day, but now 1.5 hours, taking into account the delivery of water in half an hour. Two wash and all washed.
The idea is good. The only weak point so far is a 12-volt relay through a 12-volt light bulb. In order for the voltage of the power supply to be distributed between them approximately equally, you need to choose the right lamp. And it is better, if possible, to rebuild the power supply to 12 V.

We advise you to read:

Hand it for the smartphone ...