» Furniture » Beds and sofas »DIY backlit bed

DIY backlit bed




How to make a platform for a bed do it yourself and what would she look stylish and unusual? The master made such a bed, and we will analyze how he made it in this article.

Tools and materials:

-LED Strip Light;
-Two sockets with USB ports;
-The wire;
-Tester;

-Extension;
-Board;
-Plywood;
-A screwdriver;
-Fasteners;
-Screwdriver;
- Clamps;
-Hammer;
- Terminal strip;
- dowels;
-Roulette;
- Electric jigsaw;

- Danish oil;
-Miter saw;
-Black paint;
-Brush;
-Grinder;
-Glue;

Step One: Lumber Harvesting
The first step, the master cuts off the size of the parts of the bed. Then it processes them with a grinder with sandpaper of different grain sizes. The boards of the bed frame are painted black.





Step Two: The Headboard
The headboard is made of boards fixed on a plywood sheet. First, the master sews two plywood sheets. Then screws the boards on them. The lower part of the headboard is painted black, everything else is covered with Danish oil.







Step Three: Bedside Tables
On the sides of the bed at the head of the head, the master wants to fix the nightstands. The master makes bedside tables from a board. Fastens boards with dowels and glue. Before assembly, makes a cutout for a socket, switch and lamp. After assembling the nightstand, marks the installation site on the head and drills the mounting holes. The bedside tables will be attached to the head with bolts and threaded inserts. Covers shelves with polyurethane coating.
















Step Four: Installation
Now you need to install the wiring. To the rear of the headboard along the contour, the master attaches the rail. Sticks on the rail LED strip. LED lights are screwed to the bottom of the nightstands. Sets the switch. Installs outlets. Makes wiring from the wall outlet to the outlet in the nightstands. Checks the installation by the tester.

















Step Five: Bed Frame
Assembles the bottom frame. Boards are fastened together by corners and metal plates. In the middle of the frame sets the board. Along the perimeter, from the inside, the beam is screwed. The beam is screwed 5 cm below the edge of the frame. Installs cross rails.








A board is screwed to the upper part along the perimeter of the frame. Screws the frame to the head.








The bed is ready, it remains only to install a mattress.










The whole process of making a bed can be seen in the video.
10
7.9
9.3

Add a comment

    • smilesmilesxaxaokdontknowyahoonea
      bossscratchfoolyesyes-yesaggressivesecret
      sorrydancedance2dance3pardonhelpdrinks
      stopfriendsgoodgoodgoodwhistleswoontongue
      smokeclappingcraydeclarederisivedon-t_mentiondownload
      heatirefullaugh1mdameetingmoskingnegative
      not_ipopcornpunishreadscarescaressearch
      tauntthank_youthisto_clueumnikacuteagree
      badbeeeblack_eyeblum3blushboastboredom
      censoredpleasantrysecret2threatenvictoryyusun_bespectacled
      shokrespektlolprevedwelcomekrutoyya_za
      ya_dobryihelperne_huliganne_othodifludbanclose
8 comments
And not to mention the protruding corners of the frame.
"Get your feet off the bed" They must first be lifted there without injuries!
I was already approaching half asleep to the bed, I was sitting down, throwing my legs over, and lying down. And then he came up, stumbled and you were already lying down - a reduction in time, but then slipping out slippers was dreary! xaxa
Quote: pogranec
Why I need him here, I still do not understand.
There, the author himself did not understand, you won’t understand without a bottle. But if you figure it out, you’ll hurt yourself at night with this stupid step.
Although ... What if it is an obstacle for snakes? They have them in Africa in bulk. )))
This fechral is a high-resistance alloy. Perhaps it provides for something like a car cigarette lighter.
This is an anti-alcohol bed.)) For weaning from drunkenness. You wake up from a hangover in the middle of the night, you want to go to the kitchen, take a sip of water or beer. Get your feet off the bed, try to move on, and then bam! (((A step in the most unexpected place.)))
Author
Well, maybe it translated incorrectly, but following the link we see such characteristics
Diameter: 0.64mm / 22 AWG
Wire Shape: Round; Temperature: Annealing
1.31 Ohm / ft Resistance at room temperature
Maximum Continuous Operating Temperature 1400 ° C / 2550 ° F
Temperature resistant up to 1500 ° C / 2730 ° F (melting point)
Why I need him here, I still do not understand.
Maybe in the video explains? I'll see at home. And now I have telephone traffic.
I think this is the specificity of computer translation, drew attention to the standard of sockets?
Author
In the description of the manufacture did not understand what kind of Resistance wire and why is it needed on led downlight. Who is in the know, enlighten.

We advise you to read:

Hand it for the smartphone ...