» From sites » Specialist »A useful tool that will be useful to both the joiner and the locksmith

A useful tool that will be useful to both the joiner and the locksmith


Good day to all. Today the author of the channel "Country craftsman "will show us how he made a simple but very useful device for his workshop.

To make your own homemade, the author used.

MATERIALS: wooden beam 100x50;
TOOLS: circular saw;

That's all that the author used to make this device.

And so, the author cut off from a bar, a piece of arbitrary length.


After, on a circular saw put the disk at an angle of 45 degrees. Then he took the workpiece and made a couple of cuts in it.


It turned out so far. But the author’s goal is to cut out this triangle.

Therefore, he raised the disc a little, and again went over the previously made cuts on the workpiece.

And so the author did, until he achieved the desired result.

But that’s all, the homemade product is ready.

Setting it up is very simple, just lower the drill into the center of the recess, and slightly turning the drill so that the drill is exactly in the center of the recess.

Well, the homemade product is set up and ready to go. It can be fixed in this position with a clamp or simply held with your hand during work, as the author does.

And she works like that. Suppose you need to make a hole in the pipe exactly in the middle, of course you could pinch the pipe in a vice and make a hole, but in this case the drill can go a little to the side, but this will not happen with this homemade product, it will hold the workpiece exactly in the center of the drill.

Result.

Another example, you needed to install a cotter pin on a bolt, and for this you need to make a hole in it, with this device it will not be difficult to do this.


Also, this homemade product can be used in carpentry. The author has a round blank with a diameter of 10 mm, and the master needs to make part of this blank with a diameter of 8 mm.

To do this, he installs the device exactly in the center of the disk, then he sets the workpiece in a homemade product and adjusts the disk so that the tooth height is 2 mm higher than the workpiece.

And slowly, in a circular motion, removes excess material from the workpiece.

Like this.I would like to say to the author, thank you very much for the simple but very useful home-made.

And on this, I have everything. Thanks to all! And see you soon!
8.9
9.7
9.3

Add a comment

    • smilesmilesxaxaokdontknowyahoonea
      bossscratchfoolyesyes-yesaggressivesecret
      sorrydancedance2dance3pardonhelpdrinks
      stopfriendsgoodgoodgoodwhistleswoontongue
      smokeclappingcraydeclarederisivedon-t_mentiondownload
      heatirefullaugh1mdameetingmoskingnegative
      not_ipopcornpunishreadscarescaressearch
      tauntthank_youthisto_clueumnikacuteagree
      badbeeeblack_eyeblum3blushboastboredom
      censoredpleasantrysecret2threatenvictoryyusun_bespectacled
      shokrespektlolprevedwelcomekrutoyya_za
      ya_dobryihelperne_huliganne_othodifludbanclose
5 comments
Well, not new at all ...
Guest Sergey
If you follow this instruction, then when you raise the saw by 2 mm, the diameter of the part will decrease by 4 mm, i.e. there will be not 8, but 6mm.
For fitters, this device is called, if I don’t confuse, prism, included in the set of machine tools, repeat it from wood - why not, the thing is really convenient.
The most sensible home-made of those that I saw. Simple and to the point!
Guest Vladimir
Thanks. A very necessary fixture. I will definitely do it.

We advise you to read:

Hand it for the smartphone ...