» Fixtures » Instruments »Multifunctional bending tool with four radii from the brake disc

Multifunctional bending tool with four radii from the brake disc

Hello dear readers andthe inhabitants of our site!
Already many options for bending devices have been proposed by various authors. And each of them has various advantages and disadvantages.
In this article, the author of the YouTube channel “Workshop Diy” will tell you about his version of such a tool, which implements the ability to bend workpieces with different radii.

Materials
- Old brake disc, wheel bearing
- Steel strip, round timber, pipe
- Bolts, washers
- Solidol.

Instruments, used by the author.
— 
- Cleaning and cutting discs
— 
— 
-, metal drills
- Grinder
- Hammer, square, marker, wrench.

Manufacturing process.
For the manufacture of the base you will need an old brake disc, and a functioning wheel bearing.

First of all, you need to refine the disk, and clean it from rust. The author pounds the main dirt from the inside of the disk with a hammer.


All surfaces are treated with a cleaning disc.



Finishes stripping with a Velcro disc with sandpaper.


Now the wheel bearing must be installed in the center of the brake disc. In order to make it better welded, the master grinds one outer face on the machine.




To accurately center the bearing, the author uses an ordinary round magnet.


Then the disc turns over and the bearing is welded to it.


The scale gets off, the seam is cleaned.


The result is such a basis fixtures.


Billets are cut from a steel strip for stops and handle elements.


In the main part of the lever, on which the pins will be installed, drills holes for the bolts.



Near one edge of the lever (it will be located in the center of the bearing) two steel rectangles are welded.


Next, bolts are inserted into the holes, and their heads are welded to the strip.


The third and longest bolt is welded on the underside of the lever.


The master will use a steel round log as a handle. He cut off part of it, and welded to the outer edge of the strip.


After stripping, the second part of the structure turned out. Now the rollers need to be put on the bolts, their author made of steel pipe. The length of the rollers is slightly shorter than the length of the bolts.



Now you need to apply solid oil, and put the rollers on the bolts.



To prevent the rollers from jumping off the axles, washers are welded to the edge of the bolts.



The finished structure remains to be welded to the central part of the bearing.


Also, two stops are welded to the brake disc.



Three holes for mounting screws are drilled at the outer edge of the disc, and countersink.

The last bolt with roller is installed through the standard hole in the disk.



That's all, the fixture is ready, it needs to be screwed to the workbench.



So, the first test will be a piece of reinforcement, the author bends it at the smallest radius, getting 90 degrees.


On the second radius, he tries to bend a steel square, and everything comes out perfectly.



On the third ring is already trying to bend a steel strip.


Well, the largest radius is the outer one. For him, you need to fasten the stop to the workbench.


I thank the author for a simple but useful tool for the workshop!
All good mood, good luck, and interesting ideas!

Author video can be found here.
9.4
9.2
9.4

Add a comment

    • smilesmilesxaxaokdontknowyahoonea
      bossscratchfoolyesyes-yesaggressivesecret
      sorrydancedance2dance3pardonhelpdrinks
      stopfriendsgoodgoodgoodwhistleswoontongue
      smokeclappingcraydeclarederisivedon-t_mentiondownload
      heatirefullaugh1mdameetingmoskingnegative
      not_ipopcornpunishreadscarescaressearch
      tauntthank_youthisto_clueumnikacuteagree
      badbeeeblack_eyeblum3blushboastboredom
      censoredpleasantrysecret2threatenvictoryyusun_bespectacled
      shokrespektlolprevedwelcomekrutoyya_za
      ya_dobryihelperne_huliganne_othodifludbanclose
7 comments
Yes, I did. But others are hanging, but they are not gaining so much. Look, I wrote how I’ll adapt it to angle grinder for angle grinder. Well, normal homemade. Low cost and finished product. No I do not like. And even put it on the top, she won’t gain much
Author
Well, do not forget, the system put your article in the popular. Yes, the system itself does this, not Nikolai. Yes, you wait 100K - you will have a bonus of 500 re =) for 50K 250 re
Usually, views immediately jump.
Author
So this is a response to your article. We will see.
They’ll scream that they’re cooking ninja xaxa
Strange people. This homemade product didn’t gain a thousand, although in terms of functionality, and the availability of the material is better than the one I described. But my 80 thousand gained.
I used to write Vise Bender a little more than 3000. Also a little weak.
What the people need is incomprehensible.
Author
Yes, the same idea was - you need to carve a few rings as linings, well, or bend on the same device. drinks
GMag
Cool idea, only the bearing must be sought. And you can make more radii!

We advise you to read:

Hand it for the smartphone ...