» Modeling » Aviation »Aircraft model AlIS-05" Mezon-M "

Model AlIS-05 "Mezon-M"

Hello, modelers. Again I wanted to chat with you.
This time I want to tell you about the amazing model.
It is unusual in all its appearance, very light and quite simple to manufacture.

This model, which I am telling you about, can be made much simpler, but experience comes with time and through errors. It all started with this video clip seen on YouTube.

Subsequently, such a plan appeared - a drawing, according to which, in fact, I made my model.

As usual, the drawing I saw was taken as a basis for me, and I left the silhouette of the model, like that of the Maison’s model.
I showed you this model.

I estimated the scale of the model under my existing one. electronics, put down the sizes and began to work.
As the material for the model, I chose a simple, sheet substrate for a blue laminate, this size - 1000 X 500 X 5 mm.

Glue at this moment in my possession, was waterproof, universal "CIN".

To give a beautiful appearance to the model, I used colored tape.
Here is the electronics I prepared for this model.
Motor - 2826/6 2200kV.
Model AlIS-05

The regulator is 30A.

Screw - 7 X 6.

Servos - MG 90S.

Battery - 3S 1500 maH

The model is 1120 mm long.
Span - 820 mm.
Flight weight - 350 g.
The model is made from the calculation of starting with a hand.

This time we had to cut two planes, which later, when glued, form the main frame of the model.


Inside this frame, between the upper and lower planes, inclined partitions are glued, which create volume and give strength to the whole structure.


He carved out keels, which also when installed in their place serve as load-bearing struts between the lower and upper plane of the entire model.

I had to tinker a bit with the bow of the model, my tongue turned to pronounce the word fuselage. He, as such, is not on this model.



Pay attention to the original design of the hatch on top of the body, which serves not only to access the electronics. When you start the model, it opens, the model takes on the front edge of the hatch and starts. In flight, the hatch is closed under the pressure of incoming air and is fixed with a magnetic latch.


He began to glue the model with colored tape a little.





In the tail of the lower plane, cut off the elevons and hung them directly on colored, black tape.
He made the necessary inscriptions, pasted red stars.

Glued a piece of insulation "Penoplex", which glued a piece of hardboard (fiberboard). A motor will be mounted on it.




















The whole structure turned out to be light and openwork.
At the end of construction, the model was adopted by the new chief designer of "Push", tested for strength.
















You look from the side. As if two wings connected by partitions, like biplanes.
View of the model from below.

Later, to strengthen the nose, pasted an additional strut.
Installed a motor, mounted servos.
This is how the model looks at the prelaunch stand.








Photos with the model, as a keepsake.


That's all for today.
Goodbye, see you soon again. Your valerian.
10
10
10

Add a comment

    • smilesmilesxaxaokdontknowyahoonea
      bossscratchfoolyesyes-yesaggressivesecret
      sorrydancedance2dance3pardonhelpdrinks
      stopfriendsgoodgoodgoodwhistleswoontongue
      smokeclappingcraydeclarederisivedon-t_mentiondownload
      heatirefullaugh1mdameetingmoskingnegative
      not_ipopcornpunishreadscarescaressearch
      tauntthank_youthisto_clueumnikacuteagree
      badbeeeblack_eyeblum3blushboastboredom
      censoredpleasantrysecret2threatenvictoryyusun_bespectacled
      shokrespektlolprevedwelcomekrutoyya_za
      ya_dobryihelperne_huliganne_othodifludbanclose
10 comments
Author
Actually, my name is Vyacheslav Sudakov, and I publish my flocks under the name of my grandfather! The fact is that this site was created for that, so that we can earn some money. And I don’t take offense at normal criticism, even welcome. But when someone tries to discuss me, not my models, I don’t like it and it’s unacceptable on this site! I have no doubt in your abilities and do not pretend to be palm. I show my work, which I’ve been building for 9 years. Thank you for understanding.
Valerian Arsentyevich, the fact is that half of the “regulars” here can do this, or even better. In your industry.
Here is my tsesna, my first plane from the ceiling, and against the background there is a rocket, large:



For this yes, we are not surprised. Because we ourselves are able to do this. So do not be offended by the negative, our generation can, knows how)))
Author
You will not be surprised!
So I made a mistake.
Well, actually there is no such category, "model of ceiling tiles." The ceiling is polystyrene; to use it in the model or not is already a matter for the designer. In principle, I do not think that this is prohibited in the F1 category - free-flying models and the F-5 category - radio-controlled models of electric aircraft. Then if someone is a professional can tell. The tile and the substrate under the laminate are good in that they are ready-made foam sheets of uniform thickness, it is easy to process and glue, having ready-made blueprints, a model ready for flights can be built in a couple of evenings, on YouTube there is a whole channel dedicated to such models - a hobby Isle. And if you construct it correctly, then they are strong enough (does not apply to this model), I have kissed my cessna several times with a carrot on the ground, broken screws, a dented hood, the tail turned a little once, I had to redo it, but it flies. Actually, there are chic models that are designed specifically for this material, for example, polaris. Well, not exactly for this, behind the hill, modellers use extruded Depron and BlueCor polystyrene, the ceiling is something like our answer.

But what is the point of building the same type of aircraft in batches, which, in addition, according to some commentators, do not fly at all - yes, I also do not understand. Trampling on the spot. Having so much free time and thirst for this hobby, I would rather spend it on some unfinished construction, something with a scale of 2-2.5 meters, some sort of multi-motor like An-225. This model can really surprise you.
Actually before there was such an item in the rules, video confirmation of the work of homemade
- there was no such item
Hence the conclusion suggests itself - no one reads the article, including the admin. And there’s nothing special to read there, a bunch of similar photos duplicating each other, and sometimes even irrelevant (with a kitten for example). They bored me after the third and I was very surprised that Valerian Arsentyevich’s bgm.imdmyself.com in less than a year already had 124 homemade products, of which 60 (sixty!) Are copyrighted. It turns out that he bakes them like pies (or rather, how the children cakes in the sandbox blurts out), one in less than a week.I had several questions: firstly, where is such a lot of models stored, or are they disposable - did, photographed, disassembled? Secondly, to which category of model aircraft sport (?) Do these models belong, are competitions held? In general, if shorter, then why are we shown these models of the same type, as with one shoe? I have the feeling that in front of me a torn shoe in different angles is shown, each time adding or repainting something.
That's why, but. The author decided to reprint the half of the park flyer here, and from those articles that are like him, and where he is in the photo, I have never seen a model in the sky. It is the model that he built, and not the prototype he was guided by, etc. Actually, there used to be such an item in the rules, a video confirmation of the work of the homemade product, but it was removed from the campaign, it was not found.
I would not find fault, but ...
... for example, I did not see this author on any author’s homemade product.

We advise you to read:

Hand it for the smartphone ...