» Video » SpecialVideo »Pizza knife from the old hard drive

Pizza knife from an old hard drive


Pizza lovers will surely love the idea of ​​making pizza cutting knife from an old hard drive. The implementation of the idea is presented in this review.

As always, we advise you to start by watching the author’s footage

[media = https: //www.youtube.com/watch? v = ZuQhbIALeEo]


We need to have at hand:
- unnecessary hard drive;
- two screws;
- screwdriver;
- wooden block;
- a drill.

At the very beginning of work on an emery machine or similarly, it is necessary to make a small handle from a wooden block. Everything is done here at one’s own discretion, so the author skipped the manufacturing process and possible decoration of the handle. We will skip, moving on to the next steps.

We disassemble the hard drive. To do this, unscrew the 7 screws. The first 4 screws are on the upper washer.

After unscrewing the screws, remove the washer and the first disk, followed by another washer and the second disk. To make a knife, we need only one disk, so the second can be left aside.


Below them is a stepper motor, which is fastened by the remaining 3 screws. We also unscrew them and remove the engine by pressing on the back side.



We attach the handle to the mount of the stepper motor and mark the places where the screws will be.

Next, using a drill, a flexible shaft and a small cutter, we make a recess in the wooden handle along the diameter of the fastening of the stepper motor.



We fasten the engine to the handle.


We cut off the excess parts of the screws that may remain sticking out behind the handle.

We grind the back of the handle in the area of ​​mounting the stepper motor.

We put a washer on the engine, on top of it a metal disk and another washer. Also, in place of the second disk, you need to insert a small copper ring so that the structure scrolls well.


We turn the screws to fix the disk on the engine. According to the author, the screws need to be screwed in more tightly to reduce the gap remaining due to the fact that one of the disks was removed from the structure.


The pizza knife is ready. In the end, it remains to sharpen the disc slightly if you need to cut the pizza thinner, since the knife cuts thin pizza without any problems.
10
4
8

Add a comment

    • smilesmilesxaxaokdontknowyahoonea
      bossscratchfoolyesyes-yesaggressivesecret
      sorrydancedance2dance3pardonhelpdrinks
      stopfriendsgoodgoodgoodwhistleswoontongue
      smokeclappingcraydeclarederisivedon-t_mentiondownload
      heatirefullaugh1mdameetingmoskingnegative
      not_ipopcornpunishreadscarescaressearch
      tauntthank_youthisto_clueumnikacuteagree
      badbeeeblack_eyeblum3blushboastboredom
      censoredpleasantrysecret2threatenvictoryyusun_bespectacled
      shokrespektlolprevedwelcomekrutoyya_za
      ya_dobryihelperne_huliganne_othodifludbanclose
3 commentary
The idea is certainly not bad, but it turns out that the end does not justify the means. An old hard drive can be turned over for money, and it is much more expensive than a regular pizza knife. So it turns out that it’s easier to buy a pizza knife in the store. And also such a homemade knife is very demanding in care, the wood is likely to exfoliate from moisture and the blade itself will rust, plus it can not be sharpened often, it just grinds off, such a whimsical material.
ABOUT! And we have an old hard drive lying unnecessarily, I’ll look inside if it suits. I think my husband will cope with such a step-by-step instruction. He is my pizza lover, I often cook this dish. And behind a regular knife, the top layer of cheese stretches, the look of pizza spoils. Thanks a lot.
Not all old hard drives can be used as a “spare parts warehouse” for making pizza knives. :-)
The fact is that the “pancakes” of drives are made not only from aluminum, but also from brittle ceramics and even glass.

We advise you to read:

Hand it for the smartphone ...