Tracked wheeled all-terrain vehicle from REMIX59 from the city of Perm. A very interesting version of the layout and implementation of new ideas.
On the website, REMIX59 shares its experience in construction and calculations. A lot of videos were shot on the run-in, so at the end of the article will be given a link to all the videos about auto-make. Now let's get acquainted with REMIX59.
The idea is a tracked version.
Wheel option.
Frame design.
The general idea of the current:
ICE, internal combustion engine - Oka, VAZ 2108.
Rear axles from the VAZ-2101.
RK-transfer case from the "Niva".
The hull is a metal boat.
Support rollers - wheels from VAZ, on hubs from VAZ-2108.
The differential rotation.
Caterpillar drive- tire- caterpillar without a star.
The frame is welded from the profile, and for the evenness and parallelism of the guides, wooden guides are used.
Two rear axles from the VAZ-2101 are installed.
The engine from the Oka takes its place.
Disc brakes on the hub from the VAZ-2110.
Ventilated discs, calipers too, half shaft flange machined to 116.5 mm.
Support bracket
Brake system with hydraulic booster.
The minimum design speed is 1.137 km / h, the maximum speed is 30.09 km / h.
The truck is made of a 32 mm angle and a strip of 40x4 mm.
Instead of a leading sprocket with teeth, it is proposed to use a simple wheel.
The track width is 450 mm., The pitch between the tracks is 117 mm.
The bottom is welded from metal 2 mm thick.
1 mm iron is welded onto the sides.
For the rest, galvanized iron with a thickness of -0.55 mm was used.
The height of the sides close the engine.
Clearance, clearance - 200 mm, with a width of the middle part of 800 mm and a width of tracks of 450 mm.
Truck assembly. There are 4x5 mm strips on the track, with which the tracks cut into the rubber and reduce the rotation of the track relative to the drive wheel. The contact length of the track with the drive sprocket is 1.73 m.
Guide fangs are welded.
The first exit. video.
Installed windshield.
Welded boxes over the wing.
Transport hooks are welded.
Control levers in the cab.
Frontal hydraulic brake system car making and access through the hatch.
Front propeller shaft.
The driveshaft from the transfer case to the rear axle is standard rear from the Niva, the driveshaft from the engine to the RK is homemade, the inner CV joint is the Eye.
The control of the Oka gearbox is made of the handle and cables of a foreign car and such a mechanism of the gear change lever bolted to the wings.
The propeller is ready for installation on the stern to increase the speed of movement on the water surface, while the speed with tracks is 1-3 km / h.
The screw is attached to the hull of the boat.
Mounting the propeller axis to the hull of the boat.
Wheel axle mount. Base and kerchiefs made of 5 mm steel, water pipe, finger and hub 2108. Departure from the body to the hub plane 305 mm.
The first voyage showed that counting along the waterline displaces about 880 kg. True, the bodywork is not yet done. Video
This view became after painting and installing lighting devices on tracked all-terrain vehicle.
The propeller is installed. Steering wheels.
The driver's seat.
Sealed compartments for things of 160 liters each.
Hinged hood seat provides good access to the engine for maintenance.
Shift lever and water steering control.
Water Testing.video
Designer Alexey (REMIX59), creator Andrey (a.akulov1984) and an all-terrain vehicle.
Damage to aluminum mount. Will have to make metal.
The distance between the bridges is 1800 mm.
Middle hub plate 200x190x5 mm.
Plates front and rear in place.
The width of the boat in the middle part is 800 mm, the height is 480 mm (little is needed 520 mm), the height of the side is 340 mm.
Reinforcement goes from the bridge flange horizontally to the nearest crossbeam of the frame using a vertical strut 20x20 mm, slope profile 50x20x4 mm, face 50 mm vertically. Cook after welding the side skin of the boat. Making a square hole in it for the slope to pass is easier than then mounting it in parts.
.
Now REMIX59 and a.akulov1984 continue to build other car models and good luck to them in their favorite business.