» Fixtures »PVC pipe stand for laptop

PVC pipe stand for laptop

PVC pipe stand for laptop

Assembled and not difficult to assemble and comfortable enough in operation, laptop stand assembled do it yourself. Using such a stand makes working with a laptop not only more convenient, but also extends the life of the device, because the cooling holes remain open. The cost of time and money for the manufacture of such a stand is minimal; no special knowledge or skills are required.

To create a stand from:

- PVC pipe, 0.75 inch
- PVC elbows, 6 pcs.
-hacksaw
-spray-spray
-sandpaper
-marker
-roulette
wet duster
-roulette
-glue

A detailed step-by-step description of creating a laptop stand made of PVC pipes.

Step one.
At first, the author armed himself with a tape measure and a marker in order to measure the necessary distances by points. 24 cm distances were measured; 40.8 cm; 57.6 cm; 63.6 cm and 69.6 cm from one edge of the pipe.


Step Two
Following the measured points, the PVC pipe was sawn into the necessary components to assemble the stand.

The result is just such an ordered set of tubes.

Step Three
Then the author took a part of the pipe 24 cm long and fixed elbows at its ends.


Step Four
Then they took two more identical pieces of PVC pipe 6 cm long and installed in the free holes of the elbows from the previous part.



Step Five

Then two more elbows were taken and fixed on the free ends of the short PVC pipes. Moreover, the author turned his elbows 90 degrees relative to the base of the structure.


Step Six
Tubes 16.8 cm long were taken, and elbows were also fixed at their ends. Then these parts of the pipes with elbows are installed in the previously made base for the stand. The photo shows how to deploy it.


Seventh step.
Further, each corner of the almost finished stand was aligned.


Step Eight.


Those parts of the stand that should not move should be treated with sandpaper and then glued. You can remove excess glue with a damp cloth.

After drying, you get a finished stand for a laptop from a PVC pipe.

The stand is quite convenient in that due to the large number of moving parts, you can easily adjust the angle of the laptop, and if the stand is not used, it can be conveniently folded and it will not take up much space. Also, if you wish, you can paint the stand and give it a more pleasant appearance.
8
8
8

Add a comment

    • smilesmilesxaxaokdontknowyahoonea
      bossscratchfoolyesyes-yesaggressivesecret
      sorrydancedance2dance3pardonhelpdrinks
      stopfriendsgoodgoodgoodwhistleswoontongue
      smokeclappingcraydeclarederisivedon-t_mentiondownload
      heatirefullaugh1mdameetingmoskingnegative
      not_ipopcornpunishreadscarescaressearch
      tauntthank_youthisto_clueumnikacuteagree
      badbeeeblack_eyeblum3blushboastboredom
      censoredpleasantrysecret2threatenvictoryyusun_bespectacled
      shokrespektlolprevedwelcomekrutoyya_za
      ya_dobryihelperne_huliganne_othodifludbanclose
3 commentary
1. Well, maybe so ... That's why I wrote "As for me." I myself never lie with a laptop - it’s more convenient with a tablet ...
... Although, it is also not clear, if you lie, then what is the laptop on, along with this device? On the couch?
2. What? Rear? How exactly can they be twisted if the corners are 90 degrees tight! Anyway, the back lift will be equal to the length of the short “vertical” tubes.
3. Anyhow to the benefit ...)))))))
Author
1) to make it comfortable to watch lying in any position
2) twist the tubes in the fittings obviously
3) you need more roulettes to the roulette god.
As for me, only if fittings and pipes are lying around, then from great boredom you can collect such fear ...))))
Please explain:
1. why tilt the laptop?
2. "..... ..... How ?! How exactly here you can adjust the angle?
3. Why two roulettes? ))))))))) (joke. it’s clear that just a typo)

We advise you to read:

Hand it for the smartphone ...