» Fixtures »Vacuum cleaner from an old computer hard drive

Vacuum cleaner from an old computer hard drive


Hello to all lovers homemade and just those who like to see the site in search of interesting and useful. As usual in our time, old things are disposed of in the most ordinary way, this is dumped in landfills, but sometimes it happens that something useful can be collected from an object that has failed or lost its basic qualities, in other words, give a second life. In this homemade product, the author shares with us the idea of ​​creating a vacuum cleaner from a hard drive that is not able to work as a drive due to its long service life.

To assemble a vacuum cleaner do it yourselfto us will need :
* A hard drive from a computer that is not able to function normally as a drive or is simply unnecessary.
* Plastic ribbon.
* Glue "second".
* Canvas hacksaw metal.
* Thick cardboard or thin plywood of your choice.
* Insulation tape.
* Thermogun.
* Filter, which can serve as an unnecessary stocking, pantyhose or sock.

After all the components are available, you can begin to manufacture a vacuum cleaner.
The first step is to disassemble the hard drive and free it from unnecessary parts that we don’t need,
Be careful when disassembling, as many elements are glued to a strong adhesive and can be injured when tearing.


When only the engine and the disk remain in our hard drive, then we proceed to gluing the blades, which in finished form will look like an impeller. With the glue "second" should also be shown cautionsince its drying time is an instant.

After that, we need to make a hole in the cover for air supply and its exit from the system, we do this with a metal file.

Now it is necessary to make a duct from thick cardboard, as the author did.

We heat the gun with hot glue and glue the duct to the cover of our disk, for convenience we glue it at an angle.


The place on the reverse side where the air will exit should have a filter, or debris will fly out, for this you can use a stocking or sock.

In order to complete the homemade work, it is necessary to fix our filter with electrical tape and connect the computer power supply, if it is used separately, it is necessary to close the green wire with black, simulating the power button on the computer.

On this, the homemade product is ready, all successful homemade products and unusual and useful ideas for their creation, as well as special thanks to the author Lisin.
7
7.7
5.7

Add a comment

    • smilesmilesxaxaokdontknowyahoonea
      bossscratchfoolyesyes-yesaggressivesecret
      sorrydancedance2dance3pardonhelpdrinks
      stopfriendsgoodgoodgoodwhistleswoontongue
      smokeclappingcraydeclarederisivedon-t_mentiondownload
      heatirefullaugh1mdameetingmoskingnegative
      not_ipopcornpunishreadscarescaressearch
      tauntthank_youthisto_clueumnikacuteagree
      badbeeeblack_eyeblum3blushboastboredom
      censoredpleasantrysecret2threatenvictoryyusun_bespectacled
      shokrespektlolprevedwelcomekrutoyya_za
      ya_dobryihelperne_huliganne_othodifludbanclose
14 comments
I will not ask about impeller balancing, but I note that the spindle speed of 7200 rpm and the gyroscopic effect are very noticeable.
And eta such vintyuki and gayushki))))))
Valery,
Unless boutiques
and what is it?
Yes, it would be necessary to untwist yes to throw out the excess ... I do not need magnets - I have a dime a dozen of diode ... Mirrors there are also not so hot)))). Unless boutiques ....)))))
I don’t know what to do with them ...
Disassemble, give wife 15 mirrors, pick up magnets will be useful smile
Well, I’m talking about the same ...
... I have about fifteen vintars lying ... I do not know what to do with them ... Vacuum cleaners for me are ninnadas .... And they are no longer suitable for anything ...
he powered it with a 12 V battery.
Yes, I didn’t look right from the PSB but from the PSU
Dmitrij, correctly say, the author remained with the controller in place, he was powered by a 12 V battery.
Valeryread here, three-phase motors there. And the pulse generator is on the hard drive board.
Asynchronous is a bit different)))))
I did not delve into the topic, but the usual frustration comes to the source in the computer. If there is a geknerator, then inside the vintar ...
hole in the cover for air supply and its exit from the system, we do this with a metal file.
Your untruth, uncle! There, first holes were drilled around the circumference, and then the inside was removed, most likely by biting.
And with the help of a hacksaw blade, the author cut off part of the lid from the "exhaust" side.
strange, maybe the engine is how old ... Right now they are asynchronous, or whatever they are called there. They work only at a certain frequency that the generator sets.
Ilya did not insert the video, in the original the video seems to work. He writes simply through yusb connected.
everything is cool, it’s bad only that such engines without a special controller do not work (

We advise you to read:

Hand it for the smartphone ...