» Topics » Questions »Chainsaw sharpening machine

Chainsaw Sharpening Machine

Topics / Questions
Added 13 comments
Chainsaw Sharpening Machine

I want to buy a sharpening machine. Who had the experience? Maybe there are some features, what to pay attention to? Or who model will advise specific?
Question \ topic is automatically published in the social. site network - stay tuned for answers there:
2
Added 13 comments

Suitable for topic

Related topics

Add a comment

    • smilesmilesxaxaokdontknowyahoonea
      bossscratchfoolyesyes-yesaggressivesecret
      sorrydancedance2dance3pardonhelpdrinks
      stopfriendsgoodgoodgoodwhistleswoontongue
      smokeclappingcraydeclarederisivedon-t_mentiondownload
      heatirefullaugh1mdameetingmoskingnegative
      not_ipopcornpunishreadscarescaressearch
      tauntthank_youthisto_clueumnikacuteagree
      badbeeeblack_eyeblum3blushboastboredom
      censoredpleasantrysecret2threatenvictoryyusun_bespectacled
      shokrespektlolprevedwelcomekrutoyya_za
      ya_dobryihelperne_huliganne_othodifludbanclose
13 comments
0
Reply To quote A complaint
Quote: Makcim
and saws fine

Well, these are your conclusions ... for each his own "normal" !?
0
Reply To quote A complaint
Well, I sharpen and saw normally
0
Reply To quote A complaint
Quote: Makcim
better with a chain file for longer

Well, firstly, you won’t file the file correctly, and it’s a muddy lesson (the last century). Secondly, dad told me: - "Take care of the car, not the spikes." Not that you save.
0
Reply To quote A complaint
better with a chain file for longer
0
Reply To quote A complaint
By the way, what I want to ask. Why are there many provisions in these machines? I use the "Calm-180". Sharpened “Husqvarna” and “Makita” - at all 30 degrees. And on the machines, graduation to any angle. Who knows, there are saws with a different angle in the teeth? And which ones?
In the "homemade" I did not even think about it - I made a fixed position only 30 degrees in both directions.
0
Reply To quote A complaint
He also started with Friendship. (She is dusting now. I don’t know what to do with her). Then the Urals was - his brother took it. In them, in my opinion, it is easier to sharpen. Just too many teeth))))
+1
Reply To quote A complaint
And somehow I didn’t learn to sharpen well with a file ... Correct - yes! And if after the nails - then patience was not enough for each tooth to shuffle for half an hour ....
0
Reply To quote A complaint
If you sharpen yourself and wisely, then it will serve for a long time on the machine. It’s just that those who sharpen for money so that each tooth can be cut off very quickly without looking sharpening ... Maybe it’s good that the motor is weak in my “Chinese” - but you can cut it too long, you don’t cut too much. Six seconds are needed for each tooth. The motor from the washing machine coped faster - there it was possible to pull the chain stronger.
And in this there is concern the abundance of plastic parts.True, in mine, in order to turn the plate under the other side of the chain, it was necessary to unscrew two bolts.))))) But it was stronger. And this bottom swivel is comfortable, but plastic ...
+1
Reply To quote A complaint
Not anymore. This summer I took it apart ... When I did, I took a duralumin plate (I don’t know why) for the main part, in which there was a large diameter hole on one side. There I built a motor from a Soviet washing machine. On the other hand, the plate was axially attached to a corner bent at the desired angle and spring-loaded. (You can bend the motor down). All this is compiled on a thick board that sticks forward from the workbench. And on the protruding part at an angle of 30 degrees - a brass bar in which I saw a groove under the chain ...
This summer I decided to unscrew it from the workbench and take it to the construction site - I had to cut a lot there. When he unscrewed it, he could not restrain it and it smacked on the concrete floor. The plate cracked, and, as always, “bolted” .... I wanted to redo everything, but there was absolutely no time with the construction. Temporarily just fixed the motor on the board and tried to sharpen it like that. Not convenient. A friend brought back from Ukraine for $ 30 ready. With that he took off the saw blade and set it until the diamond cup of the drill drilled ...
0
Reply To quote A complaint
A grinder than an ordinary cutting wheel? I also manually point, under the template. I used to grind without it. One way or another, with a file, the chain lasts a very long time. Although someone like sharpen of course.
0
Reply To quote A complaint
Modern saws have fewer teeth than old ones. And tooth grinding is easier. I sharpen by hand, jogging. It is possible on the grinder (the grinder is fixed) or the corresponding sandpaper. The grinding angle can be set with a simple fixture. I point it out, there is already experience. It turns out fine, not the first year. He began to sharpen on the old saw "Friendship" then "Ural".
0
Reply To quote A complaint
And where is your home-made, once said? May I take a look?
0
Reply To quote A complaint
It was homemade. I broke it. I wanted to restore everything, but my hands didn’t get through.)))) I took it apart, took out a motor, and bought a cheap "Evrotek SCG002" ... Don’t take it. Weak !!! Sharpen for a long time. (I do not have experience working with other household appliances, maybe they are all like that.)

DIY categories

We advise you to read:

Hand it for the smartphone ...