» Country homemade Do-it-yourself drip irrigation

DIY drip irrigation

DIY drip irrigation
Dear site visitors, from the material presented by the author, you will learn how to make drip irrigation for vegetables and herbs on your own summer cottage.

All summer residents and gardeners are well aware of what watering is) How much water you need to drag in buckets and watering cans to provide plants with life-giving moisture. A small area requires at least 200 liters of water, which is 20 buckets, again a load on the back.

So, in order to get rid of everyday watering and excessive loads, drip irrigation was invented.
Let's consider what is needed to build it? And also watch training videos on creating a system.

Materials
1. watering hose
2. capillaries
3. clamps
4. tees
5. taps
6. water tank (plastic or metal barrel)
7. metal corner

Instruments
1. drill
2. awl
3. hair dryer
4. welding machine and grinder (for the manufacture of racks for a container of water)

The process of creating drip irrigation do it yourself.
And so, this system consists of a tank for water, a filter, a main hose and capillaries, it is also possible to install sensors that are adjustable for irrigation time and determine soil moisture, which will further remove you even from control over irrigation, everything will be done electronics.

The watering timer is installed directly on the main hose and passes water through its housing, while a valve is installed inside that opens and closes exactly according to the time you set. You can set up several watering cycles (morning-evening) or as you wish, even after an hour)

Well, let's look at the drip irrigation schemes provided by the author.


According to the scheme, it is necessary to acquire a large barrel under water, it is best if it is plastic, since it does not give rust and oxidation, and this is important !!! Because hoses and capillaries can become clogged over time. The tank also serves to sediment and warm the water to the optimum temperature. Watering is carried out with categorically defended water, otherwise you simply ruin the planted plants and remain without a crop.

But being constantly in the open air and under direct sunshine the plastic can crack. To avoid such troubles, the barrel can be covered with some kind of material or painted with paint.

Metal barrels can also be used, but they will produce rust, which is not advisable for the above reason for clogging of the hose.

The tank should be located above the ground approximately 1.5-2 meters. This is necessary to create a stable pressure. The author made a bed under the barrel from a metal corner, it is also possible to make a wooden beam and board. The main hose is connected to the bottom of the tank.
Attention!Be sure to install a strainer so that debris does not clog the system, but remains in the sump.
Further, according to the scheme, the main hose is connected, and already capillaries are connected to it.
Drip tapes can be bought at a store or made independently, for which punctures are made in a thin hose with an awl, a hot needle, a thin screwdriver, directly at the level where the root of the plant is located. But the water pressure in such a hose will be uneven, in the factory sample, this subtlety is provided and the pressure along the entire length is the same.
For a small garden, a homemade one is quite suitable.
The drip irrigation system is also very economical, it is even used on agricultural fields, where they stretch for kilometers across the field. Profitability comes first, and the result is an excellent and healthy crop.

Having created this system on your site, you will forever say goodbye to buckets and watering cans)
Now the author has more free time and in the evening, instead of running around the garden with water and ladles, he can afford to relax, read a book or watch his favorite TV show, simply by turning the tap and blocking it after a couple of hours)

This concludes my article. Thanks for attention!
Come visit often, do not miss the latest in the world of homemade goods!

This article is for informational purposes only!
9.6
9.6
9

Add a comment

    • smilesmilesxaxaokdontknowyahoonea
      bossscratchfoolyesyes-yesaggressivesecret
      sorrydancedance2dance3pardonhelpdrinks
      stopfriendsgoodgoodgoodwhistleswoontongue
      smokeclappingcraydeclarederisivedon-t_mentiondownload
      heatirefullaugh1mdameetingmoskingnegative
      not_ipopcornpunishreadscarescaressearch
      tauntthank_youthisto_clueumnikacuteagree
      badbeeeblack_eyeblum3blushboastboredom
      censoredpleasantrysecret2threatenvictoryyusun_bespectacled
      shokrespektlolprevedwelcomekrutoyya_za
      ya_dobryihelperne_huliganne_othodifludbanclose
13 comments
What kind of experience are we talking about ............ Do you pretend to Delyausam and Valery, or what?


Well, of course, it was sarcasm! ... boss
..And you believe that there was no reason for sarcasm ???

Uh ... If you noticed, then I was still quite loyal to the "scribes", in comparison, for example, with Delausam ... But now I’ll say:
... If someone decided to write an article based on someone else's material on a topic that is far from him, then you need to start by using the search and reading materials on this topic to UNDERSTAND THE ESSENCE, and not just write similar letters and words! ..
..And then others will pick up “pearls” like this:
So, in order to get rid of everyday watering and excessive loads, drip irrigation was invented.

For this HOSE was invented !!!! ...
A hose thrown in the aisle will completely save you from "everyday loads" ... xaxa
A drip irrigation was invented FOR ANOTHER REASON !!!

And we voiced this reason and reasonably denied the mistakes of the author of the article!
... And then you appear, and accuse us of .... that we did not read the name further ... (laughter, and only) ... So more than that, we still do not understand "what is the essence of this homemade. "... xaxa

Sorry, but .... try to read further the names yourself ....

What is the essence of homemade work, I understand a little better than the author of the article ... And I perfectly understand what the essence of the article itself is - WRITE SURFACE AND SELL ... "People picks up," as Bogdan Titomir used to say .... fool
Quote: North
What kind of experience are we talking about, what and who am I imposing?


".

So, to get rid of everyday watering and excessive loads, drip irrigation was invented. "."
Everything written, nothing about ?! Starting from 20 buckets of water and ending ...
"drip irrigation was invented." And you took it for the truth and "rub" ALL! Learn the truth to know.
What kind of experience are we talking about, what and who am I imposing?

Do you pretend to business and Valery, or what? The question is rhetorical, I know that you are not pretending to be. xaxa
Hhhhhhhhhh ... Special has come! He knows! nea
PS .... It’s good that there were still people who, as a child, had seen a cucumber bed at their grandmother! )))) ... And then we would have remained in ignorance .. And they have - oh-oh-experience !!! xaxa
Quote: North
They saw drip irrigation in the name and pri ... stuck to the word drip. Read on the name of what the essence of this homemade.
So, to get rid of everyday watering and excessive loads, was invented

The strangest thing about this is that you not only believe in it, but try to impose it on others.
They saw drip irrigation in the name and pri ... stuck to the word drip. Read on the name of what the essence of this homemade.
So, to get rid of everyday watering and excessive loads, was invented
you yourself switched the conversation to your own method,


I was confused by what the author wrote:
why in a thin hose punctures are made with an awl, a hot needle, a thin screwdriver, directly at the level where the plant root is."

That is, I expected that in this case you need to bury the hose. Therefore, I wrote that if the pipe is on top, then this cannot be done. You can’t also leak a hose - only a PE pipe.
... What is wrong here?

method, it does not apply to the topic and has no advantage with drip irrigation. The main disadvantage of your method is the consumption of water.

Water Consumption is the SAME! The pumping station is controlled by humidity sensors located directly in the soil. What difference does it make when it drips from above, or is injected directly into the ground under low pressure? )))
Although ... There is a difference - from the earth through spanbond it does not evaporate almost completely ... The method that you showed in the last photo is the same thing. The only difference is that “mine” is sharpened purely under a cucumber - as you know, this culture can be planted for several years in one place. And "your" is easier to dismantle and carry. That’s all ... Well, your “Vash” is better suited for crops with a large landing interval. (Cucumber on the trellis is planted at intervals of 15 cm.)

If cho ...)))). In Israel, too, was on "collective farm issues."))). But I went there "for apples", and not for cucumbers ....

PS .... There are a lot of similar pages in our biography ....
Valery, you’ve put everything upside down (I know this method when ...).
The co-author spoke clearly about drip irrigation and recommended ...

“You can buy drip tapes in a store or do it yourself, for which punctures are made in a thin hose with an awl, a hot needle, a thin screwdriver, directly at the level where the root of the plant is located."

What was my objection to ..
Quote: To Delusam
Yes, whoever decides to repeat, do not prick the pipe with a needle (heated). This will not work, just throw after this pipe with holes (sorry for you).

You, turning everything over to your ears, hit your once “Dutch technology.” Which has practically nothing to do with drip irrigation. And even more so, it does not roll for home conditions.
And I would not say a word about your capillary method of irrigation (if you would not ....
Quote: Valery
Are you in vain ...

Your next statement ...
Quote: Valery
Capillaries! ". I wrote about capillary watering, not drip
Drop watering is just one of the varieties (the most primitive and simple) of capillary watering. With industrial capillary watering, the pipe lies in the ground, and not from above! This is exactly what I noted:

Once again, you yourself switched the conversation to your own method, it does not apply to the topic and has no advantage with drip irrigation. The main disadvantage of your method is the consumption of water. What is not less important. There is no talk about such a method in the subject.

Jews are no more stupid than the Dutch and they know the price of a drop of water. I was there and met for the first time there, with drip irrigation.
In Israel, ten months there is no rain and the temperature rises to 50 degrees. Not a single Israeli plant is complete without watering.


A more modern drip irrigation, when water is brought into the ground, and not to the surface, which further saves water (due to the virtually no surface evaporation). Without compromising soil moisture.
No, dear Valery, it’s you who are wrong. I do not know what you pricked there (which pipe), but this is no longer drip irrigation. It will beat the stream, erode the soil, etc. .. even if it does not fall on the plant. Must drip.
Drop watering, its advantage, is to drip !!! but not pouring ??? And this is not drip irrigation from a punctured hole, but jet. And this is another.

... Yes, indeed, this is ANOTHER!))))). I will indicate where you made a mistake. I wrote:
The very essence capillaries in delivering water to the root through the heated soil, without getting on the stem, and, especially, leaves ...

"Capillaries!". I wrote about capillary watering, not drip
Drop watering is just one of the varieties (the most primitive and simple) of capillary watering. With industrial capillary watering, the pipe lies in the ground, and not from above! This is exactly what I noted:
And if the pipe is on top, then it is not necessary to prick ....

In the early 2000s, I worked as a commercial director and chief engineer for large-scale farm farming. One of the directions is the cultivation of cucumber (gherkin) on open ground. For technology went to the Netherlands. There they saw for the first time a capillary irrigation system. Assembled the same. The Dutch use specials. a pipe, but they have it very expensive. Therefore, we made it from a PE pipe (HDPE - low-pressure polyethylene). And they pricked the holes with a needle, tied with a copper wire to the tip of the soldering iron.
The pipe is laid in the ground at a depth of planting a cucumber in a groove "chopped" by a hiller. After that, the groove is leveled and a casket is planted next to the pipe and the supports for the trellis are clogged. The row is covered with white low density spanbond, and after that the whole field is covered with high density black. Joints of tapes located strictly along the rows of landing are unbent and fastened with brackets, temporarily opening the rows. When the cucumber sprouts, the white spanbond is removed. And later, the staples are also removed so that the black one covers the whole earth, "hugging" the stems.
All this time, the pump station delivers water to the pipe under a certain pressure. The essence of such irrigation is that under the black canvas the soil is very warm, and water is supplied directly to the roots already warmed up. Spanbond costs are offset by weeding costs. Moreover, it does not allow the earth to dry out ...
Of course, this is not for beds 2 to three.))))). This is for hectares ... But the technology is excellent: the Ophix and Octopus hybrids, for example, produced about a ton per hundred using this technology (!!!!). These are gherkins (5-9 cm). If you pluck on zelenets (9-12 cm), the yield doubles !!!
.. Well, he told me for free!))))). And he bought the thesis from the Dutch ...)))))
Gentlemen, another request to you, "MINUSITAM".
I do not deny your point of view, although it does not rely on personal experience, but on “heard-read and the Internet” and made its conclusions.
Turn on the mind, please.
Quote: Valery
The very essence of the "capillary" in the delivery of water to the root through the heated soil, without getting on the stem, and, especially, leaves ...

No, dear Valery, it’s you who are wrong. I do not know what you pricked there (which pipe), but this is no longer drip irrigation. It will beat the stream, erode the soil, etc. .. even if it does not fall on the plant. Must drip.
Drop watering, its advantage, is to drip !!! but not pouring ??? And this is not drip irrigation from a punctured hole, but jet. And this is another.
Quote: Valery
The very essence of the "capillary" in the delivery of water to the root through the heated soil, without getting on the stem, and, especially, leaves ...

Without getting on the stems ... I threw the hose and the business - let it flow little by little. From time to time, drag to a new location.
And now about the essence: DROP !!!
1. low economical water consumption
2. moisture delivery to the roots of the plant
3. a drop falls into one place without eroding the soil
4. soil moisture occurs from one point (where it drips), capillary way, not from the surface of the soil. Which prevents the formation of an unwanted crust.
5. the ability to water, regardless of plant species
6. the ability to fully automate the irrigation process
D
but, who decides to repeat, do not prick the pipe with a needle (heated).This will not work, just throw after this pipe with holes (sorry for you).

You’re in vain ...))) I injected it, and it was heated .. I screwed it to the soldering iron ... (Not personally, but under my guidance) True, the pipe was PE (do not think about hosing the hose), and it lay under a black spanbond, with a density of 60 g per meter (It was a cucumber field of one and a half hectares. It was all covered. Water was supplied under a certain pressure). And if the pipe is on top, then you do not need to stab - you will never achieve the same orientation. Some will be "into the sky", others to the side, others to the earth ... I will not say anything about the "awl" ....
The very essence of the "capillary" in the delivery of water to the root through the heated soil, without getting on the stem, and, especially, leaves ...
As it appears ALEKS888 he composed the text himself, and if he wrote it off from someone, then both of the drip irrigation have a common idea and never did it.
""
Such a statement evokes a smile, such as "So that you wouldn’t catch fish yourself, is it easier to buy it ?!" Really funny?
fool
Drop watering is one of the progressive methods of irrigation (watering).
It has long been mechanized irrigation, even on a personal site. And in the fields ??? What watering cans and buckets?
For a personal household, this method is more expensive than just a hose and sprayers, for example.
The article has a lot of "stocks", there is no desire to list and correct it. How to "rip off" the scheme from the Internet, took it for the truth and forward.
Yes, whoever decides to repeat, do not prick the pipe with a needle (heated). This will not work, just throw after this pipe with holes (sorry for you).

We advise you to read:

Hand it for the smartphone ...