» Slingshot »How to make a shooting web shooter for office wars from paper with your own hands!

How to make a shooting web shooter for office wars from paper do it yourself!

Good day, lovers of office wars! Today decided to do stealth, shooting weapons from paper, more precisely a paper web shooter, only it will not shoot with a web, but with paper shells.

And so for a paper web shooter we need:
paper, 4 sheets of type A4
-Money gum 2-3 pieces
thermal glue
-scissors


And so the first thing you need to roll a thin tube of paper, for this we tuck one edge and start twisting, the finer the tube turns out, the better. After we make one tube, we make another, all we need is 2 thin tubes


Now around a thin tube, you need to wind a thick one (after winding a thin tube you need to remove it from a thick one), you just need to make 2 thick tubes


We divide one of the thick tubes approximately by sex:

Cut off the end because it is thin:

Glue one of the halves as best as possible on top of the whole tube:

We cut off the end from the lower duct at an angle of 45-60 degrees, as shown in the photo:

Now we need a sort of arm sleeve where we will all fasten, this sample was sewn to me by my sister, and I use it for my projects. You can also use a paper sleeve.



We try on and figure out how we will glue our blank, then glue:


Take a thin tube and cut off its thin ends:

Make a bend 2 centimeters from the edge:

Then we drive as much hot glue as possible, and wait until it hardens

We put on 2 or 3 elastic bands:

We glue everything as shown in the photo, you also need to tighten everything tightly with threads, everything should be very tight

Then we need to cut off the edge from our workpiece so that the rest of the balls is 1 cm smaller than the upper tube:

Now insert this workpiece into the upper tube:

We take another thin tube, cut off its thin ends, then make a 3-4 cm small bend, as shown in the photo (this will be our trigger) and fix with a drop of hot-melt adhesive:


From it, we cut off the edge at a slight angle, and drive the hot-melt adhesive:


Insert our “trigger” into the lower tube:

And so our web shooter is ready, it remains only to make shells. To do this, take a cut piece of a thin tube, cut it from 1.5-2 cm and pour hot melt into it. You can also use just a rolled up piece of paper.


That's it! In order to shoot from it, you need to put it on your hand as shown in the photo, take the thin tube with the rubber bands back, hook it on the edge of the lower tube, insert the projectile, aim and click on the lower thin tube. The lower tube will move the upper one and our web shooter will shoot. The thing is pretty cool and funny, it shoots about 4-5 meters long and up to 2 meters is pretty accurate.




Thank you all for your attention!
9.8
9.3
8.8

Add a comment

    • smilesmilesxaxaokdontknowyahoonea
      bossscratchfoolyesyes-yesaggressivesecret
      sorrydancedance2dance3pardonhelpdrinks
      stopfriendsgoodgoodgoodwhistleswoontongue
      smokeclappingcraydeclarederisivedon-t_mentiondownload
      heatirefullaugh1mdameetingmoskingnegative
      not_ipopcornpunishreadscarescaressearch
      tauntthank_youthisto_clueumnikacuteagree
      badbeeeblack_eyeblum3blushboastboredom
      censoredpleasantrysecret2threatenvictoryyusun_bespectacled
      shokrespektlolprevedwelcomekrutoyya_za
      ya_dobryihelperne_huliganne_othodifludbanclose

We advise you to read:

Hand it for the smartphone ...