» Fixtures »Finalization of the tool organizer step-ladder

Refinement of the tool organizer stepladder

Refinement of the tool organizer stepladder
Dear visitors of the site, from the master class presented by the author, you will learn how to independently modify the step-ladder, namely, attach an organizer to it from ordinary PVC pipe, where you can place tools, fasteners, a screwdriver and so go)

This revision of the stepladder was made for the reason that when making any repairs at a height, it is inconvenient to hold the tool and it was necessary to go down and climb the ladder for every trifle. And having attached a kind of box for screws and other fasteners, tools in the form of screwdrivers, pliers are inserted into specially drilled holes, and a small piece of PVC pipe was specially screwed on the side of the stepladder for a screwdriver.

To make repairs with such a modified stepladder is a pleasure, you don’t have to jump anywhere, everything is at hand, I don’t want to work)))

So let's look at what exactly will be needed to finalize the stepladder? And we will analyze in stages the entire master class.

Materials

1. PVC tube
2. metal screws
3. stepladder

Instruments

1. universal tool
2. hacksaw
3. sandpaper
4. knife
5. conical drill
6. marker
7. ruler
8. gas burner

Step-by-step instructions for finalizing the stepladder do it yourself.

First of all, the author prepared everything necessary, namely a stepladder and PVC pipe and all the necessary tools, so that in the process of work the master would have everything at hand.
Next, a plastic pipe is taken and superimposed on the stepladder, the marker marks the place that needs to be sawed off.
Saw the pipe with a hacksaw for metal, having previously placed it on the table, you can clamp it in a bench vice or press it with a clamp to the table.
After which the author takes a universal tool and sets the division to 1.5-2, you no longer need to, otherwise the pipe will melt.
Cut grooves for further installation on a stepladder.
Here is such a blank.
Trying on necessarily.
It fits perfectly if you can trim a bit.
Then again we remove and marking is done to cut the lid, mark it with a marker and a ruler.
Then we take a conical drill, load it into a drill or a screwdriver.
We drill holes of different diameters for the tool you have available.
We cut along the intended contour with the help of a station wagon.
Next, the lid must be bent and here ATTENTION!!! it is necessary to bend with heating the surface using a burner, so that the plastic becomes pliable and takes the shape we need. The author did not do this at the beginning and the lid on the fold cracked, but according to him, she did not lose her functionality) So please be careful.
And so, the organizer is completely ready.
We proceed to install this device on the stepladder, insert it into its rightful place and fasten it with metal screws with a press washer.
For the screwdriver, the author also provided an adaptation in the form of a small piece of PVC attached to the stirrup of the ladder.
We place the tool, fasteners, screwdriver and proceed to repair)
Now it has become much more convenient to work, because everything you need is right at your fingertips.
Well, here is such a very useful homemade product.
As you can see, in order to simplify your work, sometimes you just need to turn your wit and brainwash, as the author did. Now, by his example, you can do it too, there’s nothing complicated here, everything is simple and clear. It will take a little material, so that can be considered a revision of the budget. So we take and do. Go for it friends!

This concludes the article. Thank you all for your attention!
Come visit often and do not miss the latest in the world of homemade goods!
9
9
8

Add a comment

    • smilesmilesxaxaokdontknowyahoonea
      bossscratchfoolyesyes-yesaggressivesecret
      sorrydancedance2dance3pardonhelpdrinks
      stopfriendsgoodgoodgoodwhistleswoontongue
      smokeclappingcraydeclarederisivedon-t_mentiondownload
      heatirefullaugh1mdameetingmoskingnegative
      not_ipopcornpunishreadscarescaressearch
      tauntthank_youthisto_clueumnikacuteagree
      badbeeeblack_eyeblum3blushboastboredom
      censoredpleasantrysecret2threatenvictoryyusun_bespectacled
      shokrespektlolprevedwelcomekrutoyya_za
      ya_dobryihelperne_huliganne_othodifludbanclose
4 commentary
It’s like that, like ... Only this is in ideal conditions. When the stepladder is the right size, it stands on a flat floor and can easily be pushed-pushed closer, farther away from the wall ...
... In practice, it often turns out that the stepladder is too far away (and it’s impossible to get closer), while one of its legs is on three bricks, and you yourself are with one foot on the step of the stepladder (for the sake of one board, do not look for the stepladder higher sizes !!!), the other - on the ledge of the wall (otherwise you do not attach a board to the wall - the length of the arms is not enough)))). And so you put this board, leveled it, pressed it with your left hand to the wall, took the screw from the belt with your right, put it with a point in your mouth, then with the right you pulled the screw from the belt, squinting (for some reason)) and put your lips on it, helping it screw (the one that was in the mouth) and screwed the board ..... F-poo-pooh !!! Further - easier! You can take your foot off the wall, become both on the stepladder, because you already rest against the wall with the left (the board will not fall already, it is in its place) ... smiles helper
.. So, in such conditions, he should be where it is easy to get it, without changing the position of the body! ...
... Moreover, you need to place it somewhere for a very short time - sometimes you need both hands ... But basically - he is in the hand! Nobody wears it on the belt ... Yes, you climb up and climb down anyway with it in your hand.))) .. That is, in the belt he "does not live", there simply is a "temporary parking" for him and this more convenient (IMHO !!!) than putting it on the stairs, because the distance from the arm to the waist is always approximately unchanged, as if you were not twisting ....)))))
Quote: Valery
I mean a special belt with loops for a "screw", screwdrivers, pencils, tape measures and other pliers, and several lockable screw compartments
The belt is a convenient thing, but, in my opinion, the “shurik” is too heavy for him, and a key can be accidentally pressed. The proposed option with mounting to the stepladder I like more.
G
1. universal tool

In my opinion, the right "multifunctional tool" is not?
Currently also engaged in "bells and whistles for the stairs." Only for the attached.One already tonight did (painted, dries). While doing it, I came up with a second one))). Photographed. It will be necessary to lay out somehow .. Only, first I’ll try it myself. If not convenient - I will not boast ....
As for this device, it is PERSONAL for me to hold such a set of tools in my belt. (I mean a special belt with loops for a “screw”, screwdrivers, pencils, tape measures and other pliers, and several lockable screw compartments.) I bought on Ali. Whenever I work at height, I use it. On the stairs (again, in my opinion), the most necessary thing is a carabiner to fasten the extension cord (sometimes runs away))) and a table for the materials you work with - a tin, for example, or chopped spotlights and so on ....

We advise you to read:

Hand it for the smartphone ...