» Country homemade »Homemade hand cultivator

Homemade Hand Cultivator

Homemade hand cultivator.

Good day to all. To each to the summer resident It is known that weed control takes a lot of time and energy. Here is the hero of our article today and the author of Alexander Polulyakh collected devicewith which weed control will be much easier. And how to collect this homemade, and what you need for this, you can find out by reading the article.

And so for this homemade work, the author will need.
Armature with a diameter of 8 mm.
Homemade Hand Cultivator

Hairpin M 10 length 250 mm.

Bushings 5 ​​pcs. can be made of metal pipe or replaced with nuts.

Nuts M 10.

Steel discs with a diameter of 150 mm. and 2.5 mm thick.

With a hole in the center of 10 mm. Can be replaced with metric discs with a angle grinder or circular saw.

Old wood hacksaw.

And a couple of M 10 bolts.

First of all, the author cut off a piece of 500 mm from the reinforcement and gave it the desired shape.



Then he screwed a couple of nuts onto the stud.


Then these nuts will be welded to the fittings.

In order not to spoil the thread on the stud during welding, the author removed it.

And after welding, set back.

Then he put a sleeve on the hairpin.

Then drive.

Hub and disc again.


Etc.

Leaving space on each side of the stud for another nut.

I cut off the excess.

After installing additional nuts.


On the edge of the stud.

And tightened them well.


Taking a couple more nuts.

The author will weld them to the reinforcement one here.

The second is here.

Like this.

After the hacksaw, the master will cut a strip 40 mm wide.


And this strip will give a U-shaped.

Well warming up the bend of the burner.



To fix this part, he will make 10 holes in these places.



The author will make these surfaces sharp, as this part will serve as a knife.


Using bolts, I installed the knife in place.

Then he additionally installed one more nut on each bolt and tightened them.

To limit the movement of the knife, the author will weld two pieces of reinforcement, as shown in the photo.


And in the end, the master will take the old chopper, cut the stalk from it with a fastener.

And weld to homemade. Such an instrument today has turned out by the author.

Test.


And that’s all for me. Thank you all and see you soon!

Roller:
3.8
5.6
4.3

Add a comment

    • smilesmilesxaxaokdontknowyahoonea
      bossscratchfoolyesyes-yesaggressivesecret
      sorrydancedance2dance3pardonhelpdrinks
      stopfriendsgoodgoodgoodwhistleswoontongue
      smokeclappingcraydeclarederisivedon-t_mentiondownload
      heatirefullaugh1mdameetingmoskingnegative
      not_ipopcornpunishreadscarescaressearch
      tauntthank_youthisto_clueumnikacuteagree
      badbeeeblack_eyeblum3blushboastboredom
      censoredpleasantrysecret2threatenvictoryyusun_bespectacled
      shokrespektlolprevedwelcomekrutoyya_za
      ya_dobryihelperne_huliganne_othodifludbanclose
5 comments
I don’t watch this author’s video at all!
Product externally slightly resembles a manual cultivator produced in Soviet times. Only that one had not wheels, but stars. Very stupid thing. And the “cultivator” presented here has thick wheels that you can drive into the ground only by sitting on it.)) Nruter correctly said - a chopper on wheels.
The video shows that the stray does not cut the roots, but cuts off the aerial part of the plants.
The author is something as far from the cultivator as the Papuan of New Guinea from the swamp with cranberries. Or just a word that he liked so much?
What does the word "cultivator" have to do with the title of the article?
This is an ordinary chopper that can be pushed / pulled.
With a hole in the center of 10 mm. Can be replaced with metric discs with a angle grinder or circular saw.
What is a "metric disk on angle grinder"? And the holes on the angle grinders and circulars are far from 10 mm.

We advise you to read:

Hand it for the smartphone ...