» Country homemade »Do-it-yourself construction of the My Sea pool

Do-it-yourself construction of the My Sea pool


Good day to all. In this article, the author of the Sergey Sergey YouTube channel will show how he made such a cool pool do it yourself.

It all started with the fact that the author had such an old, unsightly pool, and besides, the cat put his claws to it. And the author, having thought a little, decided to make his own small "sea" out of this pool. Well, how, from what and what he got as a result, you can find out from this article or simply by watching an author’s video.

MATERIALS AND TOOLS:
Old pool;
Galvanized sheet;
Brick;
Cement;
Roulette;
Shovel;
Level;
Drill - 100 mm;
Aluminum profile;
Sand;
Armature, approximately 10 mm;
Hammer;
Board;
Plate bending machine;
Welding machine;
Electrodes
Angle grinder;
Exhaust rivets;
Riveter;
Finishing strip for siding;
Profile pipe 50 mm by 50 mm;
Steel bar approximately 8 mm;
Laser level;
Profile pipe 25 mm by 50 mm;
Pipe bending machine;
Sewer plastic pipe - 110 mm;
Plastic corrugation - 110 mm;
Polystyrene sheets;
Polyurethane foam;
Extruded polystyrene foam - 50 mm;
Plastic border tape;
Wooden slats:
Film;
Construction stapler and staples to it;
Nails or screws;
Screwdriver;
Terrace board (WPC);
Clamps;
Baseline data of the pool.


And so, having decided on the place, the author proceeded to the construction site. The first thing he did was markup, according to the initial data of the pool.

After proceeded to dig a hole.


When the pit under the pool was completely dug up.

The author is not far from her; he also dug a hole under the filter.

After that, he made a couple of holes connecting the two pits, and washed them with water.


Then he expanded the holes with a drill.


After the bottom of the future pool, the author fell asleep with sand, then with the help of an aluminum profile and level leveled the sand.

And condensed with water.

Further, so that the pool was round and even, the master installed pins from the fittings, as shown in the photo.


Further, for the convenience of installing a galvanized sheet, the author temporarily installed buckets.

Like this.

Further, the edges of the galvanized sheet, the master bent.



Like this.

The edges of the sheet, the author bent with such a makeshift device.

Then the sheet set in its place.



Edges connected by rivets.


Everything turned out relatively smoothly.

To prevent the sheet from falling into the ground, the author set the bottom bar for siding to the bottom.


The author will install the ladder around the pool on a tubular foundation. To do this, he took a profile pipe 50x50x1000 mm and welded to it, pieces of a steel bar.

After digging holes under the foundation racks.

I installed racks in them and poured a solution of cement with sand and gravel.

Using a laser level leveled the sides of the pool.

Then I welded pieces of the profile pipe 25x50x500 mm to the racks. These will be the supports for the ladder.


After the profile pipe 25x50 bent two rings. One 3930 mm, the second 5000 mm.

And welded these rings to the supports.



Then he made a couple of holes in a sheet of Ø 110 mm.

In the holes connecting the pool with the filter pit, the author installed plastic sewer pipes.

He connected the pipes with the sides with a plastic corrugation.

These are the holes for the nozzle fittings.

On the outside of the side, the master installed foam sheets and glued the edges with mounting foam.

The bottom is covered with polystyrene foam.

Then set up his old pool. Due to the float, the author increased the depth by 150 mm.

Voids between the sides and the wall, the master fell asleep with soil and compacted with water.



Like this.

Further, the author took a plastic border tape and installed it on the outer ring.

According to the author, the view is more beautiful, and the dust will not blow out.


The cover for the filter pit was temporarily made of rails and film.

And also this pit, the author overlaid with brick.

Then he filled the pool with water. And fixed the terrace board on the rings.

The result is such a pool.

To cover the pool, the author sewed such an awning. In the future, the master plans to make a canopy.

The author is pleased with the result of his labors. It turned out even better than he expected.

I want to say to the author, many thanks for the excellent homemade.

And that’s all for me. Thank you all and see you soon!
10
9.6
9.9

Add a comment

    • smilesmilesxaxaokdontknowyahoonea
      bossscratchfoolyesyes-yesaggressivesecret
      sorrydancedance2dance3pardonhelpdrinks
      stopfriendsgoodgoodgoodwhistleswoontongue
      smokeclappingcraydeclarederisivedon-t_mentiondownload
      heatirefullaugh1mdameetingmoskingnegative
      not_ipopcornpunishreadscarescaressearch
      tauntthank_youthisto_clueumnikacuteagree
      badbeeeblack_eyeblum3blushboastboredom
      censoredpleasantrysecret2threatenvictoryyusun_bespectacled
      shokrespektlolprevedwelcomekrutoyya_za
      ya_dobryihelperne_huliganne_othodifludbanclose
2 commentary
Here is another video for my previous comment. Https: //yadi.sk/i/Q6Eb2VS5_P1eGA
Alexander Mikhailovich
I bought a ready-made Spanish pool when selling in AUCHAN 3.5 m with a diameter of 1.25 depth. Https: //yadi.sk/i/udGkSTiKZhFjZg I did this, also dug in, but it is on foam. And the sheets of metal on the outside of the pool have a gap of 20 cm from the plane of the earthen pit for ventilation. I already use it for 5 years. I also came up with a compact pool shelter that is dry in winter.

We advise you to read:

Hand it for the smartphone ...