» Fixtures »Forging equipment at the lowest cost

Forging equipment at the lowest cost




In this article, the Wizard will tell us how to equip a blacksmith workshop with minimal expenses. The craftsman is fond of blacksmithing since childhood. This was facilitated by his family, and the father and uncle of the master are blacksmiths.

Tools and materials:
-Old water heater;
-Ax;
-Welding machine;
-USHM;
-A metal sheet;
-Metal tube;
-Clay;
-Brick;
-Vacuum cleaner;
-Hose;
- Aluminum tape;
-Various metal blanks, sheets, etc .;
- Aerosol can with paint;
-Firewood;
- mallet;
-Boards;
-Level;
-Roulette;
-Marker;
- Joiner's glue;
-Putty knife;
-Grinder;

Step One: Blacksmith Horn
The boiler consists of a tank covered with heat-insulating material and a decorative casing. The tank is made of thick metal and, according to the master, is perfect for making a blacksmith forge. The master dismantles the casing, cleans the tank from insulation.





Cuts the tank into two parts. Legs are welded to one part.


Now you need to weld the two parts of the tank together. The master sets the second half upside down inside the first part and welds them. Then the upper part of the hearth needs to be cut, fitting to your height (for the convenience of work).





In the partition, drills 16 holes with a diameter of 12 mm. A tube is welded above each hole.




Fills the upper part with clay (along the cut of the tubes) and rams it. Lays a brick.
Both clay and brick are the most common, clay from the garden, and the brick remained after construction.



Step Two: Blower
The master uses an old vacuum cleaner as a blower.



Step Three: Anvil
The anvil master welded from various pieces of metal, what was at hand.




Step Four: Anvil Stand
Now you need to make a stand under the anvil. The master has a ring from the tank. Having secured three pieces of wood inside the ring, the master fills the entire inside with chopped firewood.










To level the surface, the master nailed two slats on the sides of the stand. I installed a board with a milling cutter on the slats. Then you just need to process the surface with a milling cutter.



Then knead carpentry glue with sawdust and putty the surface.


After the glue dries, the master polishes the surface of the stand.







Everything is ready and you can check the equipment in business. According to the master, the use of a vacuum cleaner for air supply made it possible to achieve high temperature.






8
8
7.4

Add a comment

    • smilesmilesxaxaokdontknowyahoonea
      bossscratchfoolyesyes-yesaggressivesecret
      sorrydancedance2dance3pardonhelpdrinks
      stopfriendsgoodgoodgoodwhistleswoontongue
      smokeclappingcraydeclarederisivedon-t_mentiondownload
      heatirefullaugh1mdameetingmoskingnegative
      not_ipopcornpunishreadscarescaressearch
      tauntthank_youthisto_clueumnikacuteagree
      badbeeeblack_eyeblum3blushboastboredom
      censoredpleasantrysecret2threatenvictoryyusun_bespectacled
      shokrespektlolprevedwelcomekrutoyya_za
      ya_dobryihelperne_huliganne_othodifludbanclose
6 comments
Quote: Valery

[i] [/ i]

Normally written for beginner blacksmiths, those who want to try ..
Forging equipment at the lowest cost

I read "Equipment foraKnow with minimal cost ".... A little surprised))) scratch
Quickly opened, squandered ... I caught my eye on a picturesque machete sticking in the block ...))) I was even more surprised! scare shok helper
Although he condoned that yes !!! ... The costs are minimal !!! ))))
... But, sensing a catch, I read more carefully !.))))
Ay ... Trite! Not interested...)))))
Borya, what are you doing on this site ?? You should not be interested here! ))))
Guest Boris
men do not mess up the forge in the kit (a set of hammers, an anvil, an army horn, a table, a stand is only 85,000 rubles. Pick up and work!
Author
galvanization (self-tested)
- not necessarily galvanized. Modern water heaters are coated on the inside with enamel, and the metal itself is thin. He has an old boiler, 3 mm metal. And there are also copper ones made of stainless steel.
The author was lucky that the wind was not blowing in his direction when he was cooking, otherwise a week of well-being was provided - galvanization (tested on oneself).

We advise you to read:

Hand it for the smartphone ...