» Fixtures » Machine tools »Whetstone from the engine from the washing machine

Whetstone from the engine from the washing machine


Universal and very affordable sharpener from improvised materials.

For manufacturing, you will need:

Instruments:
Drill.
Bulgarian.
Hand tools.
Welding machine. etc.

Materials:
Engine.
Metal strip.
Board (base).
Case (under electronics).
Fasteners (bolts, nuts, etc.).



And so let's go. First, we’ll take measurements of the engine for future mounting.


Then, using a vice and a hammer, we make such a bracket from a metal strip.


At the ends of future fasteners we drill two holes.


On the plank itself, we drill two holes for the bracket itself.


A piece of fiberboard will serve as a gasket under the engine, to suppress vibration.


Install the engine.


We fix it with a staple and tighten it all with bolts, adjust the washers under the caps of the nuts and bolts.






As a case, I will serve as a box. In which we make two slots for the wires.


Using the standard mount, we fix the capacitor on the case itself.


Set the switch.


We connect the electronics, the main thing here is not to make a mistake when connecting, it is best to have a multimeter, or a circuit (full on the Internet).


Initially, I wanted to set the speed regulator, but since the engine was not very resourceful, I connected the standard electronics.


In the case we make four holes for the screws.



And twist at a slight angle.


To fix the abrasive, we need two important details, these are two washers from an old grinder.


We install one of the washers as in the photo, here accuracy plays an important role.


Using welding we grab the washer and the mount is almost done.


Next, grind the puck on both sides as in the photo, so that it fits well in the grooves of the second puck.



Install the abrasive.


Then the second washer.


A little washer.


Counter washer.


And tighten the nut by 13.


From the same washing machine there was a body from the engine, from which I will make a protective cover against dust and dirt.


Cut off.


Try on.


And install.


Sharpened, I will fasten to the table with two bolts.


Before painting, we clean the surface.


And paint.


Sharpened ready.

As a result, we get such a sharpener, there are a lot of applications, polishing wheels, emery wheels, etc. can be made at will.
9
6
6

Add a comment

    • smilesmilesxaxaokdontknowyahoonea
      bossscratchfoolyesyes-yesaggressivesecret
      sorrydancedance2dance3pardonhelpdrinks
      stopfriendsgoodgoodgoodwhistleswoontongue
      smokeclappingcraydeclarederisivedon-t_mentiondownload
      heatirefullaugh1mdameetingmoskingnegative
      not_ipopcornpunishreadscarescaressearch
      tauntthank_youthisto_clueumnikacuteagree
      badbeeeblack_eyeblum3blushboastboredom
      censoredpleasantrysecret2threatenvictoryyusun_bespectacled
      shokrespektlolprevedwelcomekrutoyya_za
      ya_dobryihelperne_huliganne_othodifludbanclose
5 comments
Apparently - "Baby" ... Me too. Simply, the motor did not take out of the case ....
What washing machine does the electric motor come from? It is so small that it seems that it is from an old tape recorder.
What kind of electronics is shown in the photo?
He did the right thing, that he posted the home-made. And every spiteful person who registers for just one comment has nothing to listen to. For information, "wise men", although this is a Russian site, but here lay out homemade goods and citizens of other countries who do not know Russian so well. Correctly point out errors, the author will ask for access and correct it.
Adjust the washers. From the word "crap." Better go to evening school, teach Russian. So it is written together. The repentance. Gosh, or what? Or extinguish? What is a writer's itch? I made an article and be silent in a rag.
Such a collective farm and for sale? God forbid!

We advise you to read:

Hand it for the smartphone ...