This review will be useful to all who prefer simple and non-trivial solutions. In this article, the author of the YouTube channel "Thaitrick" will tell you what useful homemade products come from simple plastic bottles. Yes Yes! It turns out that it can replace more than a dozen technical devices.
Materials and tools.
- soldering iron
- glue gun
- Silicone
- Scissors, stationery knife
- screwdriver
- Scotch.
So, let's begin.
Tip 1: Take a bottle with a capacity of 1-1.5 liters. With a permanent felt-tip pen, draw such an oval with a small slot at the base of the bottle, and cut it out with the help of a clerical knife.
We insert a wooden pole in the neck, and fix it with a screw on the outside.
How do you like such a simple homemade fruit picker?
Tip 2: All the same bottle for 1-1.5 liters. In the bottom we burn neat holes with a soldering iron.
We put the bottle on the garden hose and wind everything up with reinforced tape or insulating tape. It is important to maintain tightness.
It turns out a simple, but very good sprinkler. Especially if there is no other alternative.
Tip 3: Cut off the top of the bottle, about a third of its length. With sharp edges, slightly dig it into the ground with a rotational movement of the hand. And now the homemade little boy is ready!
Tip 4: Cut the bottom of the bottle. From two or more plastic bags we are constructing such a structure, so that as a result one bag drags another. We pack everything in the long part of the bottle. Then cover with a cut neck from the second bottle. So it turned out, an excellent dispenser for packages with automatic feed!
Tip 5: Rain is coming. And you have a switch on the external wall of the building ... All the same, the neck of a plastic bottle glued with silicone or hotmelt to the wall will solve the problem.
Simple protection against splashes and drops!
Tip 6: Cut a liter bottle in half. We make a hole in the plug with a soldering iron. Turn it over and lower the cork down into the cut bottom of the same bottle. It turns out a good container for ice.Excess water will drain and the ice will last longer. Drink your whiskey chilled!
Tip 7: You need a rope or twine, while unwinding a bobbin, it always runs off somewhere. And in this case, a plastic bottle is indispensable. Cut her bottom and neck like this. Insert the bobbin into the bottom. Connect the ends of the bottle to get a shortened version. Bring the end of the rope through the neck. Now the bobbin will not run away, and the threads will not get tangled!
Tip 8: Broken shower in the bathroom? Attach a cap with a diameter of about 5-6 cm to the base of the bottle. Circle it along the contour. Around the circle and in the center of the resulting circle, make holes with a needle equidistant from each other. Fit the neck of the bottle onto the shower hose. Why are you not a substitute for a shower head?
Tip 9: Cut the bottom of the bottle, and then cut out the main part in this form.
In the resulting tongue, make a rectangular hole. And the container for toothbrushes, pastes, combs is ready. Especially practical when camping or in a children's camp.
Tip 10: And now you need a big eggplant. With a clerical knife, we make such symmetrical cuts in it.
At another one and a half liter bottle, cut off the neck, put eggplant on the body, circle and cut a hole along this contour.
Insert our neck there. You can either tap or glue the joint if there is no strong connection. Isn't it a great dryer for dishes in the field.
Tip 11: And from such an element of the bottle you get a great watering can!
Tip 12: We collect water in a bottle, turn it upside down, lower the neck into a plate. As soon as the water in the plate ends, air enters the bottle and the level is restored. It remains only to come up with a way to mount to the wall, or make a simple stand. It turns out a simple automatic drinker for animals.
Tip 13: And how to make a spoon out of a Coca-Cola bottle? Yes, as easy as shelling pears. Mark the contour and cut with scissors, or with a knife. Do not forget to process sharp edges with a lighter.
Tip 14: And for this homemade product you will need vinegar packaging. Cut the bottom and neck. On the upper part, where there was a neck, we make small cuts with scissors. And on the lower part we plant the cropped bottom, having previously made a hole for the hook in it. We hang this thing on a hook or nail. You now have a machine for dispensing disposable cups!
Tip 15: And again we cut the bottom. We break through two holes and stretch the laces in them. The ends are fixed with a knot. There is nowhere to put an umbrella wet from the rain - this design is just useful!
Thanks to the author for interesting ideas on the use of plastic containers!
Good luck to everyone and good mood!