» Flashlights and flashlights DIY LED flashlight

DIY LED flashlight


The LED lamp made by the master can be installed on the floor or suspended under the ceiling. The lantern is bright and shines almost 360 degrees around itself. Let's watch a short video demonstrating the operation of the lamp.

For the manufacture of the lamp, the master used the following

Tools and materials:
-Pipe plastic;
- LEDs 8 mm 0.5 W - 42 pcs;
- Transformer 24 V 1 A;
-Switches - 3 pcs;
- IN4007 diode - 4 pcs;
- Resistors 33 Ohms 1 W - 7 pcs;
- Capacitor 100 uF 63 V;
-Bread board;
-The wire;
-Insulating tape;
-Glue;
- PVC plate;
-Metal plate;
-Fasteners;
- Canvas for metal;
-Hammer;
-Soldering iron;
-Nippers;
-Stripper;















Step One: The Case
The master makes the lamp housing from PVC pipes. The bottom of the pipe is cut in the form of a "tripod".












Step Two: Scheme
Installation of the electrical part will be carried out according to the scheme.

Step Three: Installation
Assembles a bridge rectifier.


LED panel mounts on plastic plates.





According to the diagram, a switch is installed on each LED panel, except for the end panel.



The transformer is installed inside the case.

It connects the LED panels and mounts the metal plate.






Screws the panel to the body.




The last step is screwed into the bracket. It will be possible to suspend a lamp for it.



LED lamp is ready. A few photos demonstrating his work.











6.8
5
5.3

Add a comment

    • smilesmilesxaxaokdontknowyahoonea
      bossscratchfoolyesyes-yesaggressivesecret
      sorrydancedance2dance3pardonhelpdrinks
      stopfriendsgoodgoodgoodwhistleswoontongue
      smokeclappingcraydeclarederisivedon-t_mentiondownload
      heatirefullaugh1mdameetingmoskingnegative
      not_ipopcornpunishreadscarescaressearch
      tauntthank_youthisto_clueumnikacuteagree
      badbeeeblack_eyeblum3blushboastboredom
      censoredpleasantrysecret2threatenvictoryyusun_bespectacled
      shokrespektlolprevedwelcomekrutoyya_za
      ya_dobryihelperne_huliganne_othodifludbanclose
14 comments
Similarly, punched with a dowel (evil nail) 5mm. on the M8 nut. And he also made holes in the saw blade with a punch when he made kitchen knives.
In the millimeter, he did the same, until the threaded rivets appeared ...If M6, for example, is needed - I drill a 7 mm template, pierce a (sharp) 5 mm pierce on a template and cut the thread ...
And what are you laughing at, a fairly effective way to thread in thin metal. For example, to cut M3 (um three, and um ze) we take a 2.5 mm nail, pierce the tin, and cut the thread in the hole obtained. When drilling with us, even one thread is unlikely to fit, and so two or three ...
From ... I read the same ...))))
So from it at first you still need to shake out the banderlogs!))) ... It's not that fast ... It's easier to nail! ...
And I would hang! ...
... In a forest somewhere ... On a tree ... And he himself - by running from there! )))
Bend the boa constrictor and drill it))
If the man did not die, then that means he lied about 24 V. The maximum output of the trance is 16 ... 17 V.
Author
I do not see crime. He struck with a nail, sharpened the reverse side on the sharpener and that’s it. I did it a hundred times myself.
What else? If Mowgli only has a nail and a boa constrictor! Do not punch the boa! They only need to tie something ... And to punch - with a nail!
Holes with nails, seriously? Even for India. I would have tore off my hands for such a Trudovik.
It’s normal, but I don’t know, I wouldn’t hang it, something in it is annoying. Form, probably.
Author
Ivan, it’s not recommended to watch a lot of things. By the way, what did you dislike about the lamp? For India, what is needed.
The main thing is not to show this homemade product to Ivan Pokhmelev

We advise you to read:

Hand it for the smartphone ...