» Fixtures » Instruments »DIY universal key for grinder

Do-it-yourself universal key for grinder

Hello dear readers and the inhabitants of our site!
In this article, the author of YouTube channel "Be Creative" will tell you how to make a simple universal key for the grinder.

To create this homemade product does not require much time, specific materials and tools.

Materials
- steel strip
- Bolts, nuts.

Instruments, used by the author.
- Bulgarian
- Petal stripping disc
- Vise
- marker
- A screwdriver, drills.

Manufacturing process.
To begin with, the author, using a grinder, cuts two blanks from a steel strip.

Then rounds all edges using a flap grinding disc.



On the resulting workpieces, marks the drilling sites.



Further, holding the workpiece in a vise, drills the holes first with a thin drill, and then with M4.



Connects both workpieces with a bolt and nut.




The key hooks are also assembled from bolts, one of them is pre-screwed with a lining nut.




Everything, the key is ready for testing!

Check on a standard tightening nut.




Now check on a non-standard, bored nut.






This key, of course, can be used for various purposes, as well as have other sizes. But there is only one sense in it, for loosening these specific nuts.

Thanks to the author for the interesting idea of ​​creating a universal key!

Good luck to everyone and good mood!
8
8.8
7.8

Add a comment

    • smilesmilesxaxaokdontknowyahoonea
      bossscratchfoolyesyes-yesaggressivesecret
      sorrydancedance2dance3pardonhelpdrinks
      stopfriendsgoodgoodgoodwhistleswoontongue
      smokeclappingcraydeclarederisivedon-t_mentiondownload
      heatirefullaugh1mdameetingmoskingnegative
      not_ipopcornpunishreadscarescaressearch
      tauntthank_youthisto_clueumnikacuteagree
      badbeeeblack_eyeblum3blushboastboredom
      censoredpleasantrysecret2threatenvictoryyusun_bespectacled
      shokrespektlolprevedwelcomekrutoyya_za
      ya_dobryihelperne_huliganne_othodifludbanclose
6 comments
Author
As for the metal edging, yes - there are such peppers. And cut against the wool. When the disk explodes, complain that it is defective.
I really didn’t think that anyone else had to do this key ...
When I buy a grinder, I hang it on a carnation ... There already hangs a lot ...
On a small grinder, the key is not needed - there is always a hand. If set correctly, it is always easy to remove by hand ... On the big one it happens that a metal circle on concrete cannot be removed after heavy cutting. But then, as a rule, the key does not help either. The gas helps then ... Circles for metal on the big one are also removed by hand, usually - although they are tightened more tightly, but also a larger lever - they do not cut to the nut ...
And then they also make a key ... But who needs it?)))
Although ... I saw him as a man, put a circle and ... PULLED THE NUT WRENCH !!! ))). Well, really, “we are not looking for easy ways” ... To the question: “Why?”, He answered: “So as not to unscrew!”)))). I tried to explain that the nut - self-pulling turns out ... Doesn’t want to listen !!! ... I realized that it’s useless to start explaining what needs to be put with a metal edging to the thrust plate, and not with a “picture up” !!! Let him suffer, if he likes it so much.))))
The failure of the method - in baboutmore likely to break the drill than with the conventional method.
As Comrade said Sukhov: "It is better, of course, to suffer."
Author
It's just that the author does not have a core, so he drills thin at first. I wanted to write about the diameter, I forgot to edit it.
holding the workpiece in a vice, first drills the holes with a thin drill, and then M4.
A rather unusual way of drilling. And M4 is a thread, and for a drill the corresponding parameter is called diameter.

We advise you to read:

Hand it for the smartphone ...