» For pets »Electric hamster treadmill

Hamster Electric Treadmill

Hello dear readers andthe inhabitants of our site!
Many of you adore small home animals like hamsters, but all sorts of hamster toys are often pretty standard - different wheels and the like.
In this article, YouTube’s author of The Q tells you how he made an electric treadmill for hamsters.

To make this homemade product will not be difficult even for a student, and the materials are quite affordable.

Materials
- sheet plywood
- PVC pipe
- bearings
- Electric motor with gear
— 
- Batteries 18650
- rubber band
- Reinforced tape
- Battery holder
- wires
- Bolts, nuts, washers M6
- Sandpaper
- solder
- Wood screws.

Instruments, used by the author.
— 
— 
— 
— 
— 
— 
- Ruler, pencil, marker, file, scissors.

Manufacturing process.
To begin with, the master measured the size of the hamster in order to choose the appropriate dimensions of the track.

On a sheet of plywood I marked future details of the structure, and even indicated their dimensions.


Then he cut the workpiece with an electric jigsaw, and cleaned the edges with sandpaper.



Here are the blanks.

He noted the places of fastening of bolts and screws on the side panels, drilled pilot holes and countersunk them with a 7 mm drill.




Then he assembled a side strut in which the engine with the gearbox will be installed. It needs only one guide bolt.




Amassed self-tapping screws, and connected with their help the base with the side panel.



Marked the seat for the engine, and with the help of a dremel cut it out. Finally leveled with a file.




Now the engine can be installed in place. Its shaft should be directed inside the structure.

From the PVC tube, the author cut two blanks for the rollers.

Using a crown, I cut out the adapter washer and pressed it into the end of the tube. It is she who will dress on the motor shaft.



On the other side of the tube, a bearing is pressed in.


Now the first roller is put on the motor shaft.

Bearings are inserted into the second roller on both sides, and it is put on a bolt.On the second side part, two guide bolts are already needed. They are inserted into the rollers on the other hand.


Now the screws are baited, and screwed to the base.


Then the wires are soldered to the engine, and connected to the voltage regulator. The regulator itself is connected to the battery compartment. Three 18650 batteries of 4.2 Volts are installed in the battery compartment. The total voltage will be 12.6 V.



The master attached the battery compartment and voltage regulator to the top panel using hot glue.




The author himself fastened the top panel to the racks.


Now thin sheet rubber is cut across the width of the rollers, and connected to each other by reinforced tape. It is unnecessary to pull the tape too much.




It remains to apply a couple of inscriptions, and the track is ready.



You can gradually increase the speed of the tape by rotating the knob. And of course, check this device on hamsters. Apparently - they liked it!




Thanks to the author for the simple idea of ​​an interesting toy for hamsters!
All good mood, good luck, and interesting ideas!

Author video can be found here.
0
0
0

Add a comment

    • smilesmilesxaxaokdontknowyahoonea
      bossscratchfoolyesyes-yesaggressivesecret
      sorrydancedance2dance3pardonhelpdrinks
      stopfriendsgoodgoodgoodwhistleswoontongue
      smokeclappingcraydeclarederisivedon-t_mentiondownload
      heatirefullaugh1mdameetingmoskingnegative
      not_ipopcornpunishreadscarescaressearch
      tauntthank_youthisto_clueumnikacuteagree
      badbeeeblack_eyeblum3blushboastboredom
      censoredpleasantrysecret2threatenvictoryyusun_bespectacled
      shokrespektlolprevedwelcomekrutoyya_za
      ya_dobryihelperne_huliganne_othodifludbanclose
5 comments
Author
The main thing is his awesome erysipelas! umnik
Listen, I’ve reviewed three times the moment where a hamster is measured with a barbell, like some kind of workpiece ...
With this stupid flood protection, comments are laid out twice! help
To begin with, the master measured the size of the hamster
Hamster - a barbell? Thank you, neighing from the heart! Tell the author, let him adjust ARDUIN, mileage, speed and calories! goodgood
To begin with, the master measured the size of the hamster
Hamster - a barbell? Thank you, neighing from the heart! Let the author of ARDUIN adjust, count calories! goodgood goodgood

We advise you to read:

Hand it for the smartphone ...