» Construction » Stoves, fireplaces, heating DIY miniature burner

DIY miniature burner

Hello dear readers andthe inhabitants of our site!
Many of you love outdoor recreation, but how to cook or reheat food in wet weather, or is there simply no desire to make a bonfire for this? Or maybe in your workshop or the garage not enough stove?

In this article, Alexander, the author of the Alexander Polulyakh YouTube channel, will tell you how to make a small burner from an old gas canister.

This homemade burner is very easy to manufacture, and can be repeated in home conditions.

Materials
- Gas spray
- Medical alcohol
- Sandpaper.

Instruments, used by the author.
- Pliers
—  Dremelthin metal drill
—  Calipers
- Belt sander
- Marker.

Manufacturing process.
First of all, you need to make sure that the gas cylinder is empty and there is no pressure in it. Then from its surface it is necessary to clean the paint-and-lacquer coating with sandpaper.

The bezel and skirt around the valve must be removed.



Next, the balloon must be cut into two equal halves. The author does this with a dremel, but an ordinary hacksaw for metal is also suitable.


The rim around the top of the cylinder is ground on a grinding machine, and the lid itself is removed.



Sharp edges need to be cleaned with sandpaper.

A small ring is additionally cut from the bottom of the cylinder.


Cut points are also ground.

This ring should be slightly reduced in diameter with the help of pliers.




On the remaining bottom, the author marks a ring at a distance of 15-20 mm from the upper edge.


The lid is inserted into the bottom like this.


Now 12 holes of 0.5 mm diameter are drilled around the entire perimeter of the glass.


All parts for the burner are ready, now you can assemble it. First, the cap is inserted into the cylinder.



And then both of these parts are installed inside the glass, and its upper edge is beaten with a hammer.


The upper edges are flared.

The burner is ready and can be filled with alcohol. As the tank warms up, alcohol vapor will begin to pass through the holes.



Now when device flared up, you can put the dishes, and cook food.



I thank Alexander for a simple but useful device for heating food and drinks!

If you have interesting homemade products, share them on this site. Here you will get a real reward, not a “bunch of green stuff" at the entertainment forum.


All good mood, good luck, and interesting ideas!

Author video can be found here.
5
8
7.5

Add a comment

    • smilesmilesxaxaokdontknowyahoonea
      bossscratchfoolyesyes-yesaggressivesecret
      sorrydancedance2dance3pardonhelpdrinks
      stopfriendsgoodgoodgoodwhistleswoontongue
      smokeclappingcraydeclarederisivedon-t_mentiondownload
      heatirefullaugh1mdameetingmoskingnegative
      not_ipopcornpunishreadscarescaressearch
      tauntthank_youthisto_clueumnikacuteagree
      badbeeeblack_eyeblum3blushboastboredom
      censoredpleasantrysecret2threatenvictoryyusun_bespectacled
      shokrespektlolprevedwelcomekrutoyya_za
      ya_dobryihelperne_huliganne_othodifludbanclose
4 commentary
Author
It is necessary to take a picture. The store sells at 400 re per liter. This is in the vodka department. In the pharmacy, 36 rubles per 100 grams.
It is doubtful that this design will be useful.
Guest Vladimir
So you still need to carry a can of alcohol with you! And how much will the cost of such a "light" come out? Alcohol is not cheap.
Many of you love relaxation. Outdoors, ... in the workshop or garage
I would find a more worthy (and only correct) use of alcohol in all of the above places! drinks

We advise you to read:

Hand it for the smartphone ...