» Construction » Stoves, fireplaces, heating »Marching pizza oven from the sink

Marching pizza oven

Marching pizza oven

If you often go outdoors using car, for such purposes, a miniature stove will be indispensable. it device will allow you to quickly cook delicious food with minimal energy. One author decided to use a kitchen metal sink as a material for making a small stove that would allow you to bake delicious pizza.

Materials and tools for homemade:
- double metal kitchen sink;
- grinder;
- rivets or screws with nuts;
- drill with drills;
- grill;
- a hammer and other tools.

Furnace manufacturing process:

Step one. Cut off the excess
First of all, you will need to cut off all the excess from the sink. That can be considered the ribbed part that is needed for drying dishes or other purposes, depending on who uses it and how. Wear protective gloves, thick pants and glasses, as there will be many hot sparks when cutting stainless steel.

Among other things, then you will need to cut the sink into two parts, that is, you should form two separate sinks.



Step Two Connect the two halves
In the next step, the author connects two sinks, as a result, a ready-made housing for the furnace is formed. Here you will need a drill and rivets. Instead of rivets, you can use screws with nuts.


Step Three We make a window
To install the grill grate in the oven, you need to make a suitable window size. We work with a grinder. Before cutting the window, you must decide how the stove will stand. In the author, she leans back, and stands on an edge formed in the middle. Just cut the edge in a straight line so that the stove is firmly on the ground.



Of course, for the oven to work, it is important to take care of a good air supply. For the author, the air enters through the drain hole of the sink, it should be located below the coal / firewood. Well, smoke comes out through a large window through which the grill is inserted.



Step Four Grill installation
a grid is needed to place pizza in the oven.The author for this case used the old grill grill, cutting off the excess. Adjust the width of the grate so that it fits into the oven window. On the other hand, you will need to drill a hole, the grill rod, which is the fulcrum, will enter here.





That's all, the stove is ready. To cook pizza, you need to load coal in the oven and light it. If you heat wood, then you need to wait until they burn and coals are formed. To get the smell of haze, you can put a couple of small sticks in the oven when making pizza.

0
0
0

Add a comment

    • smilesmilesxaxaokdontknowyahoonea
      bossscratchfoolyesyes-yesaggressivesecret
      sorrydancedance2dance3pardonhelpdrinks
      stopfriendsgoodgoodgoodwhistleswoontongue
      smokeclappingcraydeclarederisivedon-t_mentiondownload
      heatirefullaugh1mdameetingmoskingnegative
      not_ipopcornpunishreadscarescaressearch
      tauntthank_youthisto_clueumnikacuteagree
      badbeeeblack_eyeblum3blushboastboredom
      censoredpleasantrysecret2threatenvictoryyusun_bespectacled
      shokrespektlolprevedwelcomekrutoyya_za
      ya_dobryihelperne_huliganne_othodifludbanclose
5 comments
A picnic stove - maybe, but not camping. You won’t put this in a backpack. It does not look aesthetically pleasing. As for functionality, there are also questions. The air flow is too high, it is possible that the combustion will "suffocate". That ...
Here, honestly ... Once again, he made some refined urban dweller-couch ...
... He offers to take an expensive sink ... (I understand that it is not new. But what will happen to a stainless steel sink if, as we see, it is not wrinkled? !!!). Further, for some reason, to make an uncomfortable furnace out of it !!!
Why unsightly? ... I will explain. First of all, functionality! It is only this grid and use! You won’t put a pot or a frying pan especially ... In general, is it more convenient to cook in it than just at the stake? ... Further: in the car, how much space does it take? Moreover, it is clean until the first use, and then - soot, soot, coals and the corresponding smell ...
Again, what is the sink made of ??? (As I said, under the colloquial term "stainless steel" hundreds of different alloys are hidden !!! ") .. So, even heat-resistant stainless steel is not suitable for this purpose - it will lead and distort at the very first furnace !!! (Term" heat-resistant "shows its resistance to corrosion at high temperatures, but not mechanical strength!). Only heat-resistant is needed here !!! Because otherwise, with such a small thickness it will definitely twist!
Has anyone heard that kitchen sinks are made of heat resistant steel? )))) ... That is, as I understand it, you can’t drown too much !! So, a little bit, and so that the wind does not blow at the same time on it!
Bottom line: if you have an unnecessary sink lying around, sell it, and for the money you buy, buy 4-5mm simple iron and weld a "classic layout" stove. It will be better, and cobalt drilled to drill stainless steel, you do not have to buy! (What the author did not report))))))
... and remove the cover from the grinder ...
For the author, the air enters through the drain hole of the sink, it should be located below the coal / firewood.
We are probably looking at different photos? For some reason, the author has a drain hole in the back wall above the lattice is located.
Wear protective gloves, thick pants
... and with rolled up sleeves?

We advise you to read:

Hand it for the smartphone ...