» Topics » DIY ideas »Vibro Bot

Vibro bot



Hello! Today I will show how to make a vibro robot do it yourself from improvised means.

Materials
2 toothbrushes
Ice cream stick
CR2032 battery (you can have another similar one)
Electric motor
Ceiling tile (cardboard available)
Not big nuts
Wires
Double-sided tape
Switch
Eraser
Solder
Rosin

Instruments;
Scissors
Nippers
Thermal gun
Soldering iron

Step 1.

To get started, take toothbrushes and bite off the handles.
(One of me was already bitten off)



like this



Then we take a stick from ice cream and measure out 6cm



Then saw off these 6cm



After we glue the thermo brush pistol to the ice cream stick.





Now we take the electric motor and glue it with a thermo pistol to the stick with brushes





Step 2

We take 2 wires of about 3cm and clean them



like this



now we take a strip of double-sided tape and glue these wires there



like this



Now glue the battery on top of the wires



then wrap it



And cut the excess



Peel off the second layer of masking tape



And glue it under our robot



Step 3

Take the switch



take 2 wires of about 4cm



We clean from both sides



And solder to the switch



Now solder one end of the battery to the engine and the other through the switch to the engine



(I cut off the capacitor because it was in the way)



Then we glue the thermo gun switch to the motor







Now put the eraser on the shaft of the electric motor





We fix the screws on the double-sided tape so that robot rode straight



Now cut a piece of ceiling tile (cardboard possible) 9x3cm



Tear off the second layer of double-sided tape on the robot



And glue the ceiling tile (or cardboard)



Now we stick double-sided tape on the other side of the ceiling tile (or cardboard)



Rip off the second layer



Wrap and glue on the motor



Cut off the excess



We draw his eyes and mouth





By cutting the brushes you adjust where he goes.
It can also be adjusted by installing different nuts.
Question \ topic is automatically published in the social. site network - stay tuned for answers there:

Suitable for topic

Related topics

Add a comment

    • smilesmilesxaxaokdontknowyahoonea
      bossscratchfoolyesyes-yesaggressivesecret
      sorrydancedance2dance3pardonhelpdrinks
      stopfriendsgoodgoodgoodwhistleswoontongue
      smokeclappingcraydeclarederisivedon-t_mentiondownload
      heatirefullaugh1mdameetingmoskingnegative
      not_ipopcornpunishreadscarescaressearch
      tauntthank_youthisto_clueumnikacuteagree
      badbeeeblack_eyeblum3blushboastboredom
      censoredpleasantrysecret2threatenvictoryyusun_bespectacled
      shokrespektlolprevedwelcomekrutoyya_za
      ya_dobryihelperne_huliganne_othodifludbanclose
10 comments
... In Russia, there was a hungry year ....))))
To get started, take toothbrushes and bite off the handles.
(One of me was already bitten off)


Already brought teeth together
And I do not have a brush! I stole a paperweight office !!!!
"square" battery, light bulbs from a flashlight ....

... which were fastened with a rubber band from the bicycle camera to a short contact, and then, pressing a long one, "turned on and off the flashlight"
engine from the toy (two magnet cubes on the sides of the rotor cylinder, remember these?)

Which were fastened with plasticine to the place of the broken body of the toy "truck", the same rubber band made the drive to the "pair" of the rear wheel, and the wiring stretched to the hands, where there was the same "square" battery ....
All the same, there are eternal values ​​in this world. yes
36 years ago.
As now the picture is in front of my eyes: I am young, a shoe brush, a piece of plasticine, a motor from a toy, an eraser, a telephone wire and a square battery.
* brushed away the mean male tear of tenderness *
Compare the maximum current of CR2032 and the current consumption of your applied ED.
Unless, of course, this has already passed! I started my experiments with a “square” battery, light bulbs from a flashlight and a toy engine (do you remember two magnet cubes on the sides of the rotor cylinder?) Back in the first class, I had no idea either about current or voltage, and especially about power! smile
I do not understand why the switch? Twisted two wires and let's go! It will not go far, the battery will quickly die (if it does not fall off the vibration before)! smile Although, if the master is very young, then WITH REASON!, and experience and knowledge are acquired, there would be a desire! smile
The word "spell checker" is shorter than the words "spell checker." ;)
And the young man, perhaps, will be clearer. )))
skip text through spell checker

Or through a spell checker! ...)))) ...
Uh ... Or is entot a check-speller better? ))))
My young friend, I understand that in your class not all the rules of the Russian language are studied yet, but who prevents you from passing the text through a spell checker? This is the first.
Secondly, it seems that you are trained to use the Internet to some extent. So who bothers you before you do something, get acquainted with the technical characteristics of the equipment planned for use? Compare the maximum current of CR2032 and the current consumption of your applied ED.
I’ll keep silent about small mistakes.

We advise you to read:

Hand it for the smartphone ...