» Construction » Building a house Do-it-yourself sliding gates

DIY sliding gates


The idea to make sliding gates for the yard appeared long ago. Bali all sorts of projects, but as it turned out, many of them had significant shortcomings. About five years ago I took up this business specifically. I can’t say that I discovered America. But I have my own opinion on this device.

One of the main things in this project is to make the canvas of the gate itself correctly. Without unnecessary and at the same time strong frame. He abandoned the braces that spoil the appearance of the gate. I calculated the sizes of jumpers, quantity. In order not to burden and at the same time give the necessary rigidity.

At first, my son-in-law helped me. One is difficult because of the size.

Started with ...






Preset ...


Filled the canvas with a profiled sheet (small) while the sheets go inside the canvas.
That's how it was ..

That's how it became ..


Drive purchased, works from the remote control. Installation and installation completely independently. Very satisfied. They work flawlessly. It is especially convenient in winter, you will always open the gate, no matter what the snow. The gate is separate from the gate. I think this is right, some do it in the gates themselves.

As it were, without a deadbolt with a wire. blush
9
3
9

Add a comment

    • smilesmilesxaxaokdontknowyahoonea
      bossscratchfoolyesyes-yesaggressivesecret
      sorrydancedance2dance3pardonhelpdrinks
      stopfriendsgoodgoodgoodwhistleswoontongue
      smokeclappingcraydeclarederisivedon-t_mentiondownload
      heatirefullaugh1mdameetingmoskingnegative
      not_ipopcornpunishreadscarescaressearch
      tauntthank_youthisto_clueumnikacuteagree
      badbeeeblack_eyeblum3blushboastboredom
      censoredpleasantrysecret2threatenvictoryyusun_bespectacled
      shokrespektlolprevedwelcomekrutoyya_za
      ya_dobryihelperne_huliganne_othodifludbanclose
13 comments
I can’t say that I discovered America. But I have my own opinion on this device.
I did not notice something original in the design, my look.
I took 50 to 50, 3mm wall and cut it myself. The carriages are also self-made, as I already wrote, but I made them with the possibility of adjustment - the lower bar is made of 12mm sheet and in the corners of its hole. And in concrete, the same platform with studs (18mm) is poured. Studs below serve as anchors (poured into concrete).On top of the studs are nuts, on them are carriages and again nuts. But in vain weakened the design - no adjustment was needed. When pouring the “curbstone” I put the pipe on the bricks in its place and immediately adjusted the formwork in height so that the carriages hanging from the pipe were concreted correctly. And then he took off the pipe, welded the gates on it and hung it back. All "top to bottom" came up ....
.. Drive - the motor from the washing machine and the gearbox do not know why. Chain drive - I was afraid to make a home-made “toothy” bar, but I found the finished one for only $ 150. The amphibian did not sign an expense order for such an amount for a 4 meter strip with teeth: anguished: Therefore, a thin-walled gutter riveted below, in which the chain lies. For her drive and pulls back and forth ...
Author
")"
Of course, it is possible that way, but exact marking and installation (according to the template) is very required. In the upper part of the base I poured a powerful U-shaped channel (welded to flood valves), the size is somewhere 200mm. (was available). And at the same time, anchor bolts for carriages were welded to it. The gates themselves (4 m long and 2.2 m high. Working part, + 1.7 so-called counterbalance) turned out to be rather light, they lifted one freely during installation.
But it is advisable to buy a professional pipe together with the carriages. Sell it 6 m long (do not cut).
And what kind of professional pipes are doing now, and even you will weaken it?
+ Delausyusam: These are the questions I usually answer: "So that it was normal! ..." blush
P.S. Sorry! ... (this is the author of the question) ....
... It all depends on your specific case. From your dimensions of the gate (hence their weight, hence their configuration), in what soil will you concrete, etc.
The only thing: carriages to concrete are fastened with anchor bolts, pre-cast into concrete ... (And can it be otherwise?)
Hello, and also such questions, what is the main profile? , installation distance between carriages ?? And how is the general schematic dimensions? how the carriages were attached to concrete and to what depth were concreted, and how it is more convenient to dissolve the profiled pipe, and from the top of the centering rollers it is not visible on both sides, a chatter turns out .. thanks ..
We have a carriage + rail + motor with a drive costs about 600 tons of dollars. (This is a cheap option). You can buy carriages for $ 100-150 ... And bearings for them - for 15 ..
I did carriages myself. It was a long time ago (I changed those "self-swinging" in the country). Then I didn’t have a drilling machine and I decided that I could drill a new (not broken) hammer drill under the bearing shafts by putting in it an ordinary chuck with a “tail”. (Drilling 10-ku iron with the 18th drill will not work)))))). He marked and drilled a small diameter drill.
... The gates worked for a long time, and when after 6 years I took them off, I found that not all sub-bearings work due to misalignment of the axes.)))). And nothing ... They work fine ....
.... Now again an interesting topic, because it will be necessary to make the gates in the house that I am currently reconstructing ...
Yes, metal is good. I made boards for a tractor trailer from them ....
And you have a pig farm sorted out nearby, don’t you? blush (I'm talking about cast-iron grates)
I recognize a kindred "over-farm" soul ....: relaxed:
Author
We had an airfield in the open field, a "jump" (the so-called). In the dashing 90s, they all ravaged, and the military plucked the plates from the field and sold them. I bought a lot, everyone said; - and for what they are to you. And then, when it came down, they went too. We have half of the city private traders such fences, my neighbors in such a fence. Very strong metal, the most important thing is not rust.
Author
Valery, carriages are also purchased. I can do it myself, but I didn’t want to waste time, it’s easier to buy. Bearings are of closed type, in pairs of four pieces on each carriage. Two carriages.
These are ... (photo).

korbenzkol The most important thing is to make a good gate (canvas), to withstand dimensions, plane and rigidity. That's why I paid attention to it. The rest is not so important in the manufacture, and you can hooligan. It (the door leaf), is the main price of the gate, gadgets cost a penny.For 6-8 ty, you can buy the basic elements (set), and if you exclude any rubbish (such as catchers), then even less by 50%.
For example, carriages. What bearings did you use? Quantity? ... Or, also purchased?
smile P.S. Well, how many airfields were in the USSR !!!! .... How many runways in the open field could be put !!!!
It’s just that I would also like to have such a gate.
Author
Do you have a specific question or so? What's wrong with the drive? I wrote that I bought and installed the drive myself. What could be special there? So did this gate for about five years already. What details are you interested in?
Overview in general terms, nothing specific about the device and the drive. General view and photo of the gate frame.

We advise you to read:

Hand it for the smartphone ...